25 realistic Combination Vehicles practice questions for Arkansas CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Coupling
When uncoupling, you should:
-
A.
Lower the landing gear before pulling the kingpin release
-
B.
Lift the trailer with the fifth wheel
-
C.
Release the parking brake
-
D.
Rev the engine
Correct answer: A.
Lower the landing gear so the trailer is supported before disconnecting the kingpin.
Question 2 of 25 · Vehicle Dynamics
When you turn suddenly with a high center of gravity, the trailer can:
-
A.
Roll over
-
B.
Stop more quickly
-
C.
Track better
-
D.
Reduce fuel use
Correct answer: A.
High centers of gravity make trailers prone to rollover during sharp turns.
Question 3 of 25 · Vehicle Dynamics
Empty trucks have what kind of stopping distance compared to fully loaded ones?
-
A.
Shorter
-
B.
Same
-
C.
Longer
-
D.
Half
Correct answer: C.
Empty rigs have less traction on drive axles and require greater stopping distance.
Question 4 of 25 · Inspection
What is the proper way to test the parking brakes after coupling?
-
A.
Apply trailer parking brake and try to gently pull forward
-
B.
Drive at normal speed
-
C.
Apply foot brake repeatedly
-
D.
Disconnect glad hands
Correct answer: A.
A gentle pull forward with parking brakes set confirms holding power.
Question 5 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 6 of 25 · Coupling
When coupling, what should you do after the fifth wheel locks onto the kingpin?
-
A.
Pull the tractor forward gently to make sure the kingpin is locked
-
B.
Disconnect the air lines
-
C.
Drive away immediately
-
D.
Release the trailer parking brake first
Correct answer: A.
Tug-test by gently pulling forward with the trailer brakes set to confirm the lock.
Question 7 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 8 of 25 · Vehicle Dynamics
Off-tracking is most pronounced in:
-
A.
Single vehicles
-
B.
Long combinations and curves
-
C.
Empty trailers
-
D.
Vehicles with disc brakes
Correct answer: B.
Longer wheelbases and tighter curves cause greater off-tracking.
Question 9 of 25 · Backing
Which is correct about backing a tractor-trailer?
-
A.
Steer in the same direction you want the trailer to go
-
B.
Steer in the opposite direction you want the trailer to go
-
C.
Use the throttle to back
-
D.
Back as fast as possible
Correct answer: B.
When backing, turn the steering wheel opposite to the direction you want the trailer to move.
Question 10 of 25 · Bobtail
What happens if you bobtail (no trailer) and brake hard?
-
A.
You stop more quickly than loaded
-
B.
Drive wheels can lock and skid because there is little weight on them
-
C.
Vehicle handles like a loaded truck
-
D.
No special concerns
Correct answer: B.
Bobtailing leaves little weight on drive axles, increasing skid risk under hard braking.
Question 11 of 25 · Vehicle Dynamics
Why should you avoid sudden steering and braking with combinations?
-
A.
It wears tires faster
-
B.
It can cause jackknife or rollover
-
C.
It uses more fuel
-
D.
It scares passengers
Correct answer: B.
Sudden inputs can break traction and lead to jackknifing or rollovers.
Question 12 of 25 · Skids
What is the result of a "trailer jackknife"?
-
A.
Trailer continues straight ahead
-
B.
Trailer swings out and tractor pivots
-
C.
Trailer comes to a quick safe stop
-
D.
Trailer disengages
Correct answer: B.
In a trailer jackknife, the trailer swings out, often into adjacent lanes.
Question 13 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 14 of 25 · Skids
How can drivers avoid jackknifing?
-
A.
Brake gently and look ahead
-
B.
Adjust speed for road and weather
-
C.
Use ABS where equipped
-
D.
All of the above
Correct answer: D.
Smooth braking, appropriate speed, and ABS all reduce jackknife risk.
Question 15 of 25 · Inspection
Air leaks during pre-trip can be detected by:
-
A.
Listening for hissing
-
B.
Watching the air gauges drop
-
C.
Visually inspecting hoses and fittings
-
D.
All of the above
Correct answer: D.
Use multiple methods — listening, watching gauges, and visual inspection — to detect leaks.
Question 16 of 25 · Speed Management
What is the most common cause of fatal crashes for combination vehicles?
-
A.
Loss of control due to speed too fast for conditions
-
B.
Engine failure
-
C.
Tire blowouts
-
D.
Mechanical defects only
Correct answer: A.
Driving too fast for conditions is the leading cause of serious crashes.
Question 17 of 25 · Vehicle Dynamics
Which of these is true about the front trailer of a doubles or triples?
-
A.
It is less likely to overturn
-
B.
It is more stable
-
C.
It is more likely to overturn than the rear trailer
-
D.
It does not need brakes
Correct answer: A.
The front trailer in a combination is generally more stable than the rear trailer.
Question 18 of 25 · Vehicle Dynamics
Which of these is true about driving combination vehicles?
-
A.
They are easier to handle than single vehicles
-
B.
They are more likely to roll over and jackknife
-
C.
They use less fuel per mile
-
D.
They need fewer mirrors
Correct answer: B.
Combination vehicles require more skill and are more prone to rollovers and jackknives.
Question 19 of 25 · Mountain Driving
When should you use lower gears?
-
A.
On steep upgrades and downgrades
-
B.
In flat terrain
-
C.
In stop-and-go traffic only
-
D.
Never in a combination vehicle
Correct answer: A.
Use lower gears on grades to maintain torque and engine braking.
Question 20 of 25 · Following Distance
How can you reduce risk of rear-end collisions?
-
A.
Maintain safe following distances and watch for slowing traffic
-
B.
Drive at the speed limit always
-
C.
Use mirrors only at night
-
D.
Avoid signaling
Correct answer: A.
Use safe following distances and watch ahead so you have time to slow down.
Question 21 of 25 · Cargo
How do you know the trailer is properly loaded?
-
A.
Cargo is centered, balanced, and properly secured
-
B.
Cargo extends beyond the trailer ends
-
C.
Cargo is stacked unevenly
-
D.
Cargo is on top of the cab
Correct answer: A.
Centered, balanced, and secured loads handle predictably.
Question 22 of 25 · Inspection
You should inspect the rear of the trailer for:
-
A.
Cracked or missing lights
-
B.
Lights and reflectors are clean and operational
-
C.
Mud flap condition
-
D.
All of the above
Correct answer: D.
Check lights, reflectors, mud flaps, and license plate during pre-trip.
Question 23 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 24 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 25 of 25 · Inspection
When inspecting your trailer's wheels, what should you look for?
-
A.
Loose or missing nuts
-
B.
Cracked or broken wheel rims
-
C.
Bent or broken studs
-
D.
All of the above
Correct answer: D.
Inspect for loose nuts, cracks, bent studs, and other defects on every pre-trip.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Arkansas Office of Driver Services administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Arkansas CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Vehicle Dynamics: 7 questions
- Coupling: 5 questions
- Inspection: 4 questions
- Skids: 3 questions
- Backing: 1 question
- Bobtail: 1 question
- Speed Management: 1 question
- Mountain Driving: 1 question
- Following Distance: 1 question
- Cargo: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Arkansas until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.