25 realistic Combination Vehicles practice questions for Colorado CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 2 of 25 · Cargo
Why is securement of cargo essential?
-
A.
To prevent the load from shifting
-
B.
To prevent injury to others
-
C.
To prevent damage to the vehicle
-
D.
All of the above
Correct answer: D.
Securement protects the load, prevents shifts that affect handling, and protects others.
Question 3 of 25 · Coupling
What is the fifth wheel?
-
A.
A spare wheel
-
B.
A coupling device that connects the tractor to the trailer
-
C.
A device on the trailer to support cargo
-
D.
A type of axle
Correct answer: B.
The fifth wheel is the round, plate-shaped coupling that connects the tractor to the trailer.
Question 4 of 25 · Skids
What can cause a trailer skid in a combination vehicle?
-
A.
Locked trailer wheels and over-application of brakes
-
B.
Light loads on the trailer
-
C.
Tight steering at low speed
-
D.
High pressure in steering tires
Correct answer: A.
Locked trailer wheels cause trailer skid; reduce brake pressure to recover.
Question 5 of 25 · Coupling
What are landing gear used for?
-
A.
Supporting the front of the trailer when uncoupled
-
B.
Steering the trailer
-
C.
Powering the trailer brakes
-
D.
Lighting the trailer
Correct answer: A.
Landing gear holds up the trailer when it is not connected to a tractor.
Question 6 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 7 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
Question 8 of 25 · Combination Air
What is glad hands?
-
A.
Trailer doors
-
B.
Couplers used to join air lines from the tractor to the trailer
-
C.
Mirror brackets
-
D.
Brake levers
Correct answer: B.
Glad hands connect the service and emergency air lines between tractor and trailer.
Question 9 of 25 · CDL Rules
Which is true about long combination vehicles (LCVs)?
-
A.
They are easier to maneuver in tight spaces
-
B.
They require additional driver training and special permits
-
C.
They handle the same as single trailers
-
D.
They never require special routes
Correct answer: B.
LCVs need extra training, certifications, and often follow restricted routes.
Question 10 of 25 · Vehicle Dynamics
Why should you avoid sudden steering and braking with combinations?
-
A.
It wears tires faster
-
B.
It can cause jackknife or rollover
-
C.
It uses more fuel
-
D.
It scares passengers
Correct answer: B.
Sudden inputs can break traction and lead to jackknifing or rollovers.
Question 11 of 25 · Coupling
You should NEVER:
-
A.
Back under a trailer at an angle
-
B.
Inspect the fifth wheel
-
C.
Use the parking brake
-
D.
Tug-test the kingpin
Correct answer: A.
Backing at an angle can damage the kingpin or push the trailer sideways.
Question 12 of 25 · Backing
Which is correct about backing a tractor-trailer?
-
A.
Steer in the same direction you want the trailer to go
-
B.
Steer in the opposite direction you want the trailer to go
-
C.
Use the throttle to back
-
D.
Back as fast as possible
Correct answer: B.
When backing, turn the steering wheel opposite to the direction you want the trailer to move.
Question 13 of 25 · Coupling
When uncoupling, what is the final step?
-
A.
Lower the landing gear and disconnect electrical cord and air lines
-
B.
Drive forward immediately
-
C.
Set the parking brake on the tractor only
-
D.
Engage the trailer brakes only
Correct answer: A.
After raising the fifth wheel jaws and pulling forward, disconnect lines and lower landing gear.
Question 14 of 25 · Combination Air
What should the tractor protection valve do?
-
A.
Keep tractor air supply if trailer breaks away or develops a major leak
-
B.
Set the trailer parking brake on a hill
-
C.
Apply trailer brakes during a normal stop
-
D.
Disconnect the trailer
Correct answer: A.
It protects the tractor air supply by closing if a major air loss occurs.
Question 15 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 16 of 25 · Inspection
Air leaks during pre-trip can be detected by:
-
A.
Listening for hissing
-
B.
Watching the air gauges drop
-
C.
Visually inspecting hoses and fittings
-
D.
All of the above
Correct answer: D.
Use multiple methods — listening, watching gauges, and visual inspection — to detect leaks.
Question 17 of 25 · Inspection
Which of these is not a part of the trailer's electrical system?
-
A.
Lights
-
B.
Brake control
-
C.
Power line cord (pigtail)
-
D.
Hydraulic pump
Correct answer: D.
Hydraulic pumps are not part of standard trailer electrical systems on highway combinations.
Question 18 of 25 · Coupling
When uncoupling, you should:
-
A.
Lower the landing gear before pulling the kingpin release
-
B.
Lift the trailer with the fifth wheel
-
C.
Release the parking brake
-
D.
Rev the engine
Correct answer: A.
Lower the landing gear so the trailer is supported before disconnecting the kingpin.
Question 19 of 25 · Inspection
Which is true about gladhand seals?
-
A.
They should be replaced if cracked or damaged
-
B.
They never need replacement
-
C.
They are the same as electrical connections
-
D.
They are always made of metal
Correct answer: A.
Replace damaged or worn rubber seals to keep air from leaking at the gladhands.
Question 20 of 25 · Cargo
How do you know the trailer is properly loaded?
-
A.
Cargo is centered, balanced, and properly secured
-
B.
Cargo extends beyond the trailer ends
-
C.
Cargo is stacked unevenly
-
D.
Cargo is on top of the cab
Correct answer: A.
Centered, balanced, and secured loads handle predictably.
Question 21 of 25 · Inspection
When should you check trailer brakes during operation?
-
A.
First few miles after coupling
-
B.
Every fuel stop
-
C.
Just at the end of the trip
-
D.
Never during the trip
Correct answer: A.
Test trailer brakes early in the trip to make sure they are functioning correctly.
Question 22 of 25 · Inspection
You should inspect the rear of the trailer for:
-
A.
Cracked or missing lights
-
B.
Lights and reflectors are clean and operational
-
C.
Mud flap condition
-
D.
All of the above
Correct answer: D.
Check lights, reflectors, mud flaps, and license plate during pre-trip.
Question 23 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 24 of 25 · Skids
Which is the most common cause of trailer skid?
-
A.
Driving too fast for conditions
-
B.
Locking the rear trailer wheels by overbraking
-
C.
Worn brake shoes
-
D.
Too much trailer weight
Correct answer: B.
Trailer skids most often occur when rear trailer wheels lock during braking.
Question 25 of 25 · Following Distance
How can you reduce risk of rear-end collisions?
-
A.
Maintain safe following distances and watch for slowing traffic
-
B.
Drive at the speed limit always
-
C.
Use mirrors only at night
-
D.
Avoid signaling
Correct answer: A.
Use safe following distances and watch ahead so you have time to slow down.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Colorado Division of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Colorado CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 7 questions
- Inspection: 5 questions
- Skids: 3 questions
- Vehicle Dynamics: 3 questions
- Cargo: 2 questions
- Combination Air: 2 questions
- CDL Rules: 1 question
- Backing: 1 question
- Following Distance: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Colorado until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.