25 realistic Combination Vehicles practice questions for District of Columbia CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Vehicle Dynamics
Which of these is true about the front trailer of a doubles or triples?
-
A.
It is less likely to overturn
-
B.
It is more stable
-
C.
It is more likely to overturn than the rear trailer
-
D.
It does not need brakes
Correct answer: A.
The front trailer in a combination is generally more stable than the rear trailer.
Question 2 of 25 · Emergency Equipment
What are some common causes of vehicle fires?
-
A.
Under-inflated tires and electrical short circuits
-
B.
Improper use of flares
-
C.
Cargo that catches fire from spilled fuel
-
D.
All of the above
Correct answer: D.
All of these can cause vehicle fires. Pre-trip and en-route inspections reduce risk.
Question 3 of 25 · Coupling
What does a "low coupling" condition look like?
-
A.
Trailer is too high above the fifth wheel
-
B.
Trailer is at the right height
-
C.
Trailer is too low and tractor frame can hit the trailer
-
D.
Trailer is angled to the right
Correct answer: C.
A trailer too low can damage the tractor frame as it slides under it.
Question 4 of 25 · Inspection
When checking the trailer air supply, you should:
-
A.
Charge the trailer with air, then disconnect the supply hose to test trailer emergency brakes
-
B.
Pump the brakes
-
C.
Disconnect the trailer power cord
-
D.
Open the trailer service line manually
Correct answer: A.
Disconnecting the supply line tests that the trailer emergency brakes apply automatically.
Question 5 of 25 · Combination Air
What should the tractor protection valve do?
-
A.
Keep tractor air supply if trailer breaks away or develops a major leak
-
B.
Set the trailer parking brake on a hill
-
C.
Apply trailer brakes during a normal stop
-
D.
Disconnect the trailer
Correct answer: A.
It protects the tractor air supply by closing if a major air loss occurs.
Question 6 of 25 · Inspection
Which of these is not a part of the trailer's electrical system?
-
A.
Lights
-
B.
Brake control
-
C.
Power line cord (pigtail)
-
D.
Hydraulic pump
Correct answer: D.
Hydraulic pumps are not part of standard trailer electrical systems on highway combinations.
Question 7 of 25 · Following Distance
How can you reduce risk of rear-end collisions?
-
A.
Maintain safe following distances and watch for slowing traffic
-
B.
Drive at the speed limit always
-
C.
Use mirrors only at night
-
D.
Avoid signaling
Correct answer: A.
Use safe following distances and watch ahead so you have time to slow down.
Question 8 of 25 · Operation
Which of these is most important when driving with a trailer?
-
A.
Use the engine retarder constantly
-
B.
Use proper braking and signaling
-
C.
Drive at maximum speed limits
-
D.
Skip pre-trip checks if running late
Correct answer: B.
Proper braking and clear signaling are essential to safe combination driving.
Question 9 of 25 · Coupling
What is the proper position for the fifth wheel?
-
A.
Tilted down toward the rear of the tractor with jaws open
-
B.
Pointed straight up
-
C.
Locked and ready
-
D.
Removed for inspection
Correct answer: A.
Before coupling, the fifth wheel should tilt down toward the rear with the jaws open.
Question 10 of 25 · Skids
How can you correct a tractor jackknife?
-
A.
Apply the brakes harder
-
B.
Steer in the direction of the skid and accelerate gently
-
C.
Stop steering input
-
D.
Release the brakes and counter-steer
Correct answer: D.
Release the brakes to regain traction; counter-steer carefully to recover.
Question 11 of 25 · Combination Air
Trailer hand valve is used to:
-
A.
Test trailer brakes
-
B.
Park the trailer
-
C.
Bypass the foot valve
-
D.
Drain trailer tanks
Correct answer: A.
Use the trailer hand valve only for testing — not for parking or normal stops.
Question 12 of 25 · Following Distance
What is "rear-end collision" risk for combination vehicles?
-
A.
It is reduced when carrying long cargo
-
B.
They have a higher risk because of long stopping distances and rear blind spots
-
C.
They have no greater risk
-
D.
Only for empty rigs
Correct answer: B.
Long stopping distance and rear blind spots increase rear-end collision risk.
Question 13 of 25 · Coupling
When uncoupling, what is the final step?
-
A.
Lower the landing gear and disconnect electrical cord and air lines
-
B.
Drive forward immediately
-
C.
Set the parking brake on the tractor only
-
D.
Engage the trailer brakes only
Correct answer: A.
After raising the fifth wheel jaws and pulling forward, disconnect lines and lower landing gear.
Question 14 of 25 · Skids
Tractor jackknife occurs when:
-
A.
Drive wheels lose traction and skid
-
B.
The trailer wheels lock
-
C.
The trailer slides forward
-
D.
Steering wheels lock
Correct answer: A.
Drive wheels skidding cause tractor jackknife; trailer wheels skidding cause trailer jackknife.
Question 15 of 25 · Coupling
When uncoupling, you should:
-
A.
Lower the landing gear before pulling the kingpin release
-
B.
Lift the trailer with the fifth wheel
-
C.
Release the parking brake
-
D.
Rev the engine
Correct answer: A.
Lower the landing gear so the trailer is supported before disconnecting the kingpin.
Question 16 of 25 · Inspection
When inspecting your trailer's wheels, what should you look for?
-
A.
Loose or missing nuts
-
B.
Cracked or broken wheel rims
-
C.
Bent or broken studs
-
D.
All of the above
Correct answer: D.
Inspect for loose nuts, cracks, bent studs, and other defects on every pre-trip.
Question 17 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 18 of 25 · Combination Air
Trailer brakes are required to be:
-
A.
Adjusted properly and matched to tractor brakes
-
B.
Stronger than tractor brakes
-
C.
Disengaged on level roads
-
D.
Off when empty
Correct answer: A.
Trailer brakes must be in proper adjustment and balance with tractor brakes.
Question 19 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 20 of 25 · Cargo
What can cause a high center of gravity?
-
A.
Loading cargo too low
-
B.
Loading cargo too high or unevenly
-
C.
Driving too slowly
-
D.
Empty trailers
Correct answer: B.
Stacking cargo too high or loading unevenly raises the center of gravity and rollover risk.
Question 21 of 25 · Skids
What is the result of a "trailer jackknife"?
-
A.
Trailer continues straight ahead
-
B.
Trailer swings out and tractor pivots
-
C.
Trailer comes to a quick safe stop
-
D.
Trailer disengages
Correct answer: B.
In a trailer jackknife, the trailer swings out, often into adjacent lanes.
Question 22 of 25 · Mountain Driving
When should you use lower gears?
-
A.
On steep upgrades and downgrades
-
B.
In flat terrain
-
C.
In stop-and-go traffic only
-
D.
Never in a combination vehicle
Correct answer: A.
Use lower gears on grades to maintain torque and engine braking.
Question 23 of 25 · Cargo
Why is securement of cargo essential?
-
A.
To prevent the load from shifting
-
B.
To prevent injury to others
-
C.
To prevent damage to the vehicle
-
D.
All of the above
Correct answer: D.
Securement protects the load, prevents shifts that affect handling, and protects others.
Question 24 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 25 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The DC Department of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your District of Columbia CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 8 questions
- Inspection: 3 questions
- Combination Air: 3 questions
- Skids: 3 questions
- Following Distance: 2 questions
- Cargo: 2 questions
- Vehicle Dynamics: 1 question
- Emergency Equipment: 1 question
- Operation: 1 question
- Mountain Driving: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for District of Columbia until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.