Iowa Air Brakes CDL Practice Test
25 realistic Air Brakes practice questions for Iowa CDL applicants. Required for: Vehicles equipped with air brake systems. Official test: 25 questions, 20 correct to pass.
Question 1 of 25 · Spring Brakes
If your vehicle has dual parking control valves, you can use pressure from a separate tank to:
-
A.
Charge the trailer brakes
-
B.
Release the spring brakes to move a short distance if the main system loses air
-
C.
Operate the steering
-
D.
Power the air horn
Correct answer: B.
Dual parking control valves let you temporarily release spring brakes from a backup tank.
Question 2 of 25 · Operation
When the brake pedal is pushed harder, what happens?
-
A.
Brake pedal must be pumped to release
-
B.
More air goes to the brakes; less foot pressure releases air
-
C.
It locks the brakes permanently
-
D.
The brakes do not respond
Correct answer: B.
The harder you push, the more air pressure is sent to the brake chambers.
Question 3 of 25 · ABS
If the ABS warning light comes on, you should:
-
A.
Stop driving immediately
-
B.
Continue, knowing brakes still work — but ABS may not
-
C.
Pump the brakes constantly
-
D.
Engage the trailer hand valve
Correct answer: B.
You still have normal braking; only the ABS function may be off. Get it fixed soon.
Question 4 of 25 · Foundation Brakes
When checking the slack adjuster on S-cam brakes, the slack adjuster should not move more than:
-
A.
1/2 inch
-
B.
1 inch
-
C.
About 1 inch where the push rod attaches to it
-
D.
2 inches
Correct answer: C.
When pulled by hand, the slack adjuster shouldn't move more than about an inch where the push rod attaches.
Question 5 of 25 · Inspection
What is the air loss rate for combination vehicles with brakes applied?
-
A.
1 psi per minute
-
B.
2 psi per minute
-
C.
3 psi per minute
-
D.
4 psi per minute
Correct answer: D.
Combination vehicles can lose up to 4 psi per minute with brakes applied.
Question 6 of 25 · Emergency Maneuvers
Which of these statements is true about emergency braking?
-
A.
Pumping the brakes is always best
-
B.
Stab braking is for non-ABS vehicles in emergencies
-
C.
You should brake harder than necessary
-
D.
Stab braking is the same as pumping
Correct answer: B.
Stab braking applies to non-ABS systems: full application until lockup, then release.
Question 7 of 25 · Spring Brakes
What does the term "modulating control valve" refer to?
-
A.
A valve to regulate engine RPM
-
B.
A hand-operated valve that gradually applies the spring brakes
-
C.
A device that drains air tanks
-
D.
The trailer hand valve
Correct answer: B.
A modulating control valve allows gradual application of spring brakes for emergency or backup use.
Question 8 of 25 · Compressor
Which of these systems removes water and oil from compressed air?
-
A.
Air dryer
-
B.
Brake chamber
-
C.
Slack adjuster
-
D.
S-cam
Correct answer: A.
The air dryer removes moisture and oil from the air before it reaches the storage tanks.
Question 9 of 25 · Parking
On a tractor with no trailer attached, the tractor parking brake control:
-
A.
Will lock and unlock the front brakes
-
B.
Will set or release the spring brakes on the tractor
-
C.
Has no function
-
D.
Operates only the trailer brakes
Correct answer: B.
The yellow diamond control sets and releases the tractor parking (spring) brakes.
Question 10 of 25 · System Basics
Air brake systems combine three different braking systems. They are:
-
A.
Service, parking, and emergency brakes
-
B.
Hydraulic, parking, and emergency brakes
-
C.
Front, rear, and trailer brakes
-
D.
Disc, drum, and parking brakes
Correct answer: A.
The three are: the service brake, the parking brake, and the emergency brake.
Question 11 of 25 · Spring Brakes
Spring brakes:
-
A.
Are released by air pressure
-
B.
Are applied by air pressure
-
C.
Should be tested by pumping the brake pedal
-
D.
Are only on the trailer
Correct answer: A.
Spring brakes are held off (released) by air pressure. When pressure drops, the springs apply the brakes.
Question 12 of 25 · Inspection
How can you check the slack adjusters?
-
A.
Pull hard on each slack adjuster — they should not move more than about 1 inch
-
B.
Listen for air leaks at each chamber
-
C.
Watch the brake light flash
-
D.
Look at the brake pedal travel
Correct answer: A.
Pulling hard, slack adjusters should not move more than about 1 inch where the push rod attaches.
Question 13 of 25 · ABS
Which is correct about ABS-equipped vehicles?
-
A.
You should never use ABS
-
B.
ABS works only at high speeds
-
C.
You should drive the same way as without ABS, except brake firmly without pumping in emergencies
-
D.
ABS makes stopping distance shorter
Correct answer: C.
Drive normally; in emergencies, brake firmly and let ABS prevent lockup. ABS doesn't shorten stopping distance.
Question 14 of 25 · Speed Management
Brake fade results from:
-
A.
Oversized brakes
-
B.
Excessive heat from prolonged braking
-
C.
Too much air pressure
-
D.
Cold weather
Correct answer: B.
Brake fade is caused by overheating brakes that lose stopping power.
Question 15 of 25 · Inspection
Which of the following must be checked before operating an air-braked vehicle?
-
A.
Low air pressure warning signal
-
B.
Spring brakes set automatically
-
C.
Air leakage rate
-
D.
All of the above
Correct answer: D.
All of these are required pre-trip air brake checks.
Question 16 of 25 · Gauges
The supply pressure gauge tells you:
-
A.
The pressure of brake fluid
-
B.
How much air pressure is in the air tanks
-
C.
The trailer brake pressure
-
D.
The temperature of the brake
Correct answer: B.
The supply gauge shows the air pressure available in the storage tanks.
Question 17 of 25 · ABS
Which is true about ABS?
-
A.
It activates only on dry roads
-
B.
It activates only when wheels are about to lock during heavy braking
-
C.
It is the same as anti-skid
-
D.
It eliminates the need for skid recovery
Correct answer: B.
ABS activates only when wheels are about to lock; otherwise the brake system operates normally.
Question 18 of 25 · Foundation Brakes
Brake drums (or discs) must not have cracks longer than:
-
A.
1/4 the width of the friction area
-
B.
1/2 the width of the friction area
-
C.
3/4 the width of the friction area
-
D.
Anything is acceptable
Correct answer: B.
Cracks longer than one-half the width of the friction area are a safety violation.
Question 19 of 25 · Inspection
When should you check the parking brake?
-
A.
Whenever you start a trip
-
B.
Once a month
-
C.
Only at inspections
-
D.
When the brake warning light is on
Correct answer: A.
Test the parking brake every trip — apply the brake and try to move forward gently.
Question 20 of 25 · Inspection
When should you push the brake pedal during the air brake test?
-
A.
Only when the engine is running
-
B.
When checking the compressor
-
C.
When the engine is off, to check that pressure does not drop too quickly
-
D.
During the brake light test only
Correct answer: C.
Apply firm pressure with the engine off to check for excessive air leakage from the system.
Question 21 of 25 · Inspection
When checking air brake adjustment, the engine should be:
-
A.
Running at idle
-
B.
Off with the brakes released
-
C.
Running at high RPM
-
D.
Off with the brakes applied
Correct answer: B.
Inspect with the engine off and the brakes released so chambers are not pressurized.
Question 22 of 25 · Tanks
What is the safety valve set to open at?
-
A.
100 psi
-
B.
125 psi
-
C.
150 psi
-
D.
180 psi
Correct answer: C.
The safety valve is normally set to open at 150 psi to protect the system from over-pressurization.
Question 23 of 25 · Spring Brakes
Spring brakes will come on automatically when air pressure drops to:
-
A.
100 psi
-
B.
60 psi or less
-
C.
20 to 45 psi
-
D.
10 psi
Correct answer: C.
Spring brakes typically apply automatically between 20 and 45 psi.
Question 24 of 25 · Inspection
How do you test the low pressure warning signal?
-
A.
With the engine off, pump the brake pedal until the signal activates (must come on at 60 psi or above)
-
B.
Drive the vehicle to lose pressure
-
C.
Open the air tank drain valve briefly
-
D.
Push the parking brake control
Correct answer: A.
Pump the brake to lower pressure; warning must come on at 60 psi or higher.
Question 25 of 25 · Operation
When making a normal stop, what should you do?
-
A.
Push the brake pedal down so you can stop at a safe place and remain in control
-
B.
Pump the brakes
-
C.
Use only the parking brake
-
D.
Use only the trailer hand valve
Correct answer: A.
Apply pressure progressively to come to a smooth, safe stop while maintaining control.
About the Air Brakes Test
The Air Brakes test covers air brake system parts (compressor, governor, reservoirs, drain valves, alcohol evaporator, safety valve, brake pedal, foundation brakes), dual air brake systems, inspecting air brakes, using air brakes (normal stops, emergency stops, parking brakes), and proper procedures for braking on downgrades. If you fail or skip the Air Brakes test, your CDL is restricted to vehicles without full air brake systems.
The Iowa Department of Transportation — Motor Vehicle Division administers this knowledge test as part of its commercial driver license program. To earn the Air Brakes Endorsement on your Iowa CDL, you need to score at least 20 out of 25 on the official version.
Topics covered on this practice test
- Inspection: 7 questions
- Spring Brakes: 4 questions
- ABS: 3 questions
- Operation: 2 questions
- Foundation Brakes: 2 questions
- Emergency Maneuvers: 1 question
- Compressor: 1 question
- Parking: 1 question
- System Basics: 1 question
- Speed Management: 1 question
- Gauges: 1 question
- Tanks: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Iowa until you're ready for the official exam.
Tips specific to the Air Brakes test
Air Brakes questions test your ability to identify components, follow inspection sequences, and respond to system failures. Memorize the cut-in and cut-out pressures, the low-pressure warning thresholds, the pressure ranges at which spring brakes apply, and the maximum allowable air-loss rates. Many questions have nearly-identical wording, so precision matters.
Other practice tests for Iowa