25 realistic Combination Vehicles practice questions for Massachusetts CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Inspection
You should inspect the rear of the trailer for:
-
A.
Cracked or missing lights
-
B.
Lights and reflectors are clean and operational
-
C.
Mud flap condition
-
D.
All of the above
Correct answer: D.
Check lights, reflectors, mud flaps, and license plate during pre-trip.
Question 2 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 3 of 25 · Inspection
When should you check trailer brakes during operation?
-
A.
First few miles after coupling
-
B.
Every fuel stop
-
C.
Just at the end of the trip
-
D.
Never during the trip
Correct answer: A.
Test trailer brakes early in the trip to make sure they are functioning correctly.
Question 4 of 25 · Skids
What can cause a trailer skid in a combination vehicle?
-
A.
Locked trailer wheels and over-application of brakes
-
B.
Light loads on the trailer
-
C.
Tight steering at low speed
-
D.
High pressure in steering tires
Correct answer: A.
Locked trailer wheels cause trailer skid; reduce brake pressure to recover.
Question 5 of 25 · Vehicle Dynamics
Off-tracking is most pronounced in:
-
A.
Single vehicles
-
B.
Long combinations and curves
-
C.
Empty trailers
-
D.
Vehicles with disc brakes
Correct answer: B.
Longer wheelbases and tighter curves cause greater off-tracking.
Question 6 of 25 · Inspection
What is the proper way to test the parking brakes after coupling?
-
A.
Apply trailer parking brake and try to gently pull forward
-
B.
Drive at normal speed
-
C.
Apply foot brake repeatedly
-
D.
Disconnect glad hands
Correct answer: A.
A gentle pull forward with parking brakes set confirms holding power.
Question 7 of 25 · Skids
What is the result of a "trailer jackknife"?
-
A.
Trailer continues straight ahead
-
B.
Trailer swings out and tractor pivots
-
C.
Trailer comes to a quick safe stop
-
D.
Trailer disengages
Correct answer: B.
In a trailer jackknife, the trailer swings out, often into adjacent lanes.
Question 8 of 25 · Coupling
When uncoupling, what is the final step?
-
A.
Lower the landing gear and disconnect electrical cord and air lines
-
B.
Drive forward immediately
-
C.
Set the parking brake on the tractor only
-
D.
Engage the trailer brakes only
Correct answer: A.
After raising the fifth wheel jaws and pulling forward, disconnect lines and lower landing gear.
Question 9 of 25 · Coupling
What is the proper position for the fifth wheel?
-
A.
Tilted down toward the rear of the tractor with jaws open
-
B.
Pointed straight up
-
C.
Locked and ready
-
D.
Removed for inspection
Correct answer: A.
Before coupling, the fifth wheel should tilt down toward the rear with the jaws open.
Question 10 of 25 · Vehicle Dynamics
Which of these is true about the front trailer of a doubles or triples?
-
A.
It is less likely to overturn
-
B.
It is more stable
-
C.
It is more likely to overturn than the rear trailer
-
D.
It does not need brakes
Correct answer: A.
The front trailer in a combination is generally more stable than the rear trailer.
Question 11 of 25 · Combination Air
Trailer hand valve is used to:
-
A.
Test trailer brakes
-
B.
Park the trailer
-
C.
Bypass the foot valve
-
D.
Drain trailer tanks
Correct answer: A.
Use the trailer hand valve only for testing — not for parking or normal stops.
Question 12 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
Question 13 of 25 · CDL Rules
Which is true about long combination vehicles (LCVs)?
-
A.
They are easier to maneuver in tight spaces
-
B.
They require additional driver training and special permits
-
C.
They handle the same as single trailers
-
D.
They never require special routes
Correct answer: B.
LCVs need extra training, certifications, and often follow restricted routes.
Question 14 of 25 · Operation
Which of these is most important when driving with a trailer?
-
A.
Use the engine retarder constantly
-
B.
Use proper braking and signaling
-
C.
Drive at maximum speed limits
-
D.
Skip pre-trip checks if running late
Correct answer: B.
Proper braking and clear signaling are essential to safe combination driving.
Question 15 of 25 · Vehicle Dynamics
When you turn suddenly with a high center of gravity, the trailer can:
-
A.
Roll over
-
B.
Stop more quickly
-
C.
Track better
-
D.
Reduce fuel use
Correct answer: A.
High centers of gravity make trailers prone to rollover during sharp turns.
Question 16 of 25 · Skids
What should you do to recover from a trailer skid?
-
A.
Apply more brake pressure
-
B.
Release the brakes to allow trailer wheels to roll again
-
C.
Steer hard right
-
D.
Accelerate forward
Correct answer: B.
Release brakes to let trailer wheels roll, then steer to recover direction.
Question 17 of 25 · Cargo
How do you know the trailer is properly loaded?
-
A.
Cargo is centered, balanced, and properly secured
-
B.
Cargo extends beyond the trailer ends
-
C.
Cargo is stacked unevenly
-
D.
Cargo is on top of the cab
Correct answer: A.
Centered, balanced, and secured loads handle predictably.
Question 18 of 25 · Following Distance
What is "rear-end collision" risk for combination vehicles?
-
A.
It is reduced when carrying long cargo
-
B.
They have a higher risk because of long stopping distances and rear blind spots
-
C.
They have no greater risk
-
D.
Only for empty rigs
Correct answer: B.
Long stopping distance and rear blind spots increase rear-end collision risk.
Question 19 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 20 of 25 · Speed Management
What is the most common cause of fatal crashes for combination vehicles?
-
A.
Loss of control due to speed too fast for conditions
-
B.
Engine failure
-
C.
Tire blowouts
-
D.
Mechanical defects only
Correct answer: A.
Driving too fast for conditions is the leading cause of serious crashes.
Question 21 of 25 · Combination Air
Trailer brakes are required to be:
-
A.
Adjusted properly and matched to tractor brakes
-
B.
Stronger than tractor brakes
-
C.
Disengaged on level roads
-
D.
Off when empty
Correct answer: A.
Trailer brakes must be in proper adjustment and balance with tractor brakes.
Question 22 of 25 · Coupling
How can you keep a stiff coupling system from causing problems?
-
A.
Lubricate the fifth wheel
-
B.
Avoid backing under fast
-
C.
Inspect mounting bolts
-
D.
All of the above
Correct answer: D.
Lubricate, back slowly, and inspect mounting bolts to keep the coupling working safely.
Question 23 of 25 · Coupling
What is the fifth wheel?
-
A.
A spare wheel
-
B.
A coupling device that connects the tractor to the trailer
-
C.
A device on the trailer to support cargo
-
D.
A type of axle
Correct answer: B.
The fifth wheel is the round, plate-shaped coupling that connects the tractor to the trailer.
Question 24 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
Question 25 of 25 · Inspection
Which of these is not a part of the trailer's electrical system?
-
A.
Lights
-
B.
Brake control
-
C.
Power line cord (pigtail)
-
D.
Hydraulic pump
Correct answer: D.
Hydraulic pumps are not part of standard trailer electrical systems on highway combinations.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Massachusetts Registry of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Massachusetts CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 6 questions
- Inspection: 4 questions
- Skids: 4 questions
- Vehicle Dynamics: 4 questions
- Combination Air: 2 questions
- CDL Rules: 1 question
- Operation: 1 question
- Cargo: 1 question
- Following Distance: 1 question
- Speed Management: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Massachusetts until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.