25 realistic Combination Vehicles practice questions for Minnesota CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Operation
Which of these is most important when driving with a trailer?
-
A.
Use the engine retarder constantly
-
B.
Use proper braking and signaling
-
C.
Drive at maximum speed limits
-
D.
Skip pre-trip checks if running late
Correct answer: B.
Proper braking and clear signaling are essential to safe combination driving.
Question 2 of 25 · Vehicle Dynamics
Off-tracking is most pronounced in:
-
A.
Single vehicles
-
B.
Long combinations and curves
-
C.
Empty trailers
-
D.
Vehicles with disc brakes
Correct answer: B.
Longer wheelbases and tighter curves cause greater off-tracking.
Question 3 of 25 · Bobtail
What happens if you bobtail (no trailer) and brake hard?
-
A.
You stop more quickly than loaded
-
B.
Drive wheels can lock and skid because there is little weight on them
-
C.
Vehicle handles like a loaded truck
-
D.
No special concerns
Correct answer: B.
Bobtailing leaves little weight on drive axles, increasing skid risk under hard braking.
Question 4 of 25 · Speed Management
What is the most common cause of fatal crashes for combination vehicles?
-
A.
Loss of control due to speed too fast for conditions
-
B.
Engine failure
-
C.
Tire blowouts
-
D.
Mechanical defects only
Correct answer: A.
Driving too fast for conditions is the leading cause of serious crashes.
Question 5 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 6 of 25 · Skids
How can you correct a tractor jackknife?
-
A.
Apply the brakes harder
-
B.
Steer in the direction of the skid and accelerate gently
-
C.
Stop steering input
-
D.
Release the brakes and counter-steer
Correct answer: D.
Release the brakes to regain traction; counter-steer carefully to recover.
Question 7 of 25 · Coupling
When uncoupling, what is the final step?
-
A.
Lower the landing gear and disconnect electrical cord and air lines
-
B.
Drive forward immediately
-
C.
Set the parking brake on the tractor only
-
D.
Engage the trailer brakes only
Correct answer: A.
After raising the fifth wheel jaws and pulling forward, disconnect lines and lower landing gear.
Question 8 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
Question 9 of 25 · Skids
Which is the most common cause of trailer skid?
-
A.
Driving too fast for conditions
-
B.
Locking the rear trailer wheels by overbraking
-
C.
Worn brake shoes
-
D.
Too much trailer weight
Correct answer: B.
Trailer skids most often occur when rear trailer wheels lock during braking.
Question 10 of 25 · Mountain Driving
When should you use lower gears?
-
A.
On steep upgrades and downgrades
-
B.
In flat terrain
-
C.
In stop-and-go traffic only
-
D.
Never in a combination vehicle
Correct answer: A.
Use lower gears on grades to maintain torque and engine braking.
Question 11 of 25 · Following Distance
How can you reduce risk of rear-end collisions?
-
A.
Maintain safe following distances and watch for slowing traffic
-
B.
Drive at the speed limit always
-
C.
Use mirrors only at night
-
D.
Avoid signaling
Correct answer: A.
Use safe following distances and watch ahead so you have time to slow down.
Question 12 of 25 · Combination Air
What is glad hands?
-
A.
Trailer doors
-
B.
Couplers used to join air lines from the tractor to the trailer
-
C.
Mirror brackets
-
D.
Brake levers
Correct answer: B.
Glad hands connect the service and emergency air lines between tractor and trailer.
Question 13 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
Question 14 of 25 · Inspection
You should inspect the rear of the trailer for:
-
A.
Cracked or missing lights
-
B.
Lights and reflectors are clean and operational
-
C.
Mud flap condition
-
D.
All of the above
Correct answer: D.
Check lights, reflectors, mud flaps, and license plate during pre-trip.
Question 15 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 16 of 25 · Inspection
When inspecting your trailer's wheels, what should you look for?
-
A.
Loose or missing nuts
-
B.
Cracked or broken wheel rims
-
C.
Bent or broken studs
-
D.
All of the above
Correct answer: D.
Inspect for loose nuts, cracks, bent studs, and other defects on every pre-trip.
Question 17 of 25 · CDL Rules
Which is true about long combination vehicles (LCVs)?
-
A.
They are easier to maneuver in tight spaces
-
B.
They require additional driver training and special permits
-
C.
They handle the same as single trailers
-
D.
They never require special routes
Correct answer: B.
LCVs need extra training, certifications, and often follow restricted routes.
Question 18 of 25 · Coupling
When uncoupling, you should:
-
A.
Lower the landing gear before pulling the kingpin release
-
B.
Lift the trailer with the fifth wheel
-
C.
Release the parking brake
-
D.
Rev the engine
Correct answer: A.
Lower the landing gear so the trailer is supported before disconnecting the kingpin.
Question 19 of 25 · Inspection
Which is true about gladhand seals?
-
A.
They should be replaced if cracked or damaged
-
B.
They never need replacement
-
C.
They are the same as electrical connections
-
D.
They are always made of metal
Correct answer: A.
Replace damaged or worn rubber seals to keep air from leaking at the gladhands.
Question 20 of 25 · Cargo
What can cause a high center of gravity?
-
A.
Loading cargo too low
-
B.
Loading cargo too high or unevenly
-
C.
Driving too slowly
-
D.
Empty trailers
Correct answer: B.
Stacking cargo too high or loading unevenly raises the center of gravity and rollover risk.
Question 21 of 25 · Cargo
Why is securement of cargo essential?
-
A.
To prevent the load from shifting
-
B.
To prevent injury to others
-
C.
To prevent damage to the vehicle
-
D.
All of the above
Correct answer: D.
Securement protects the load, prevents shifts that affect handling, and protects others.
Question 22 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 23 of 25 · Inspection
Which of these is not a part of the trailer's electrical system?
-
A.
Lights
-
B.
Brake control
-
C.
Power line cord (pigtail)
-
D.
Hydraulic pump
Correct answer: D.
Hydraulic pumps are not part of standard trailer electrical systems on highway combinations.
Question 24 of 25 · Vehicle Dynamics
Which of these is true about driving combination vehicles?
-
A.
They are easier to handle than single vehicles
-
B.
They are more likely to roll over and jackknife
-
C.
They use less fuel per mile
-
D.
They need fewer mirrors
Correct answer: B.
Combination vehicles require more skill and are more prone to rollovers and jackknives.
Question 25 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Minnesota Driver and Vehicle Services administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Minnesota CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 5 questions
- Vehicle Dynamics: 4 questions
- Inspection: 4 questions
- Skids: 3 questions
- Cargo: 2 questions
- Operation: 1 question
- Bobtail: 1 question
- Speed Management: 1 question
- Mountain Driving: 1 question
- Following Distance: 1 question
- Combination Air: 1 question
- CDL Rules: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Minnesota until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.