25 realistic Doubles and Triples practice questions for Oregon CDL applicants. Required for: Drivers pulling more than one trailer. Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Coupling
What's the role of safety chains on a converter dolly?
-
A.
To support the dolly when uncoupled
-
B.
To prevent the trailer from coming loose if the pintle hook fails
-
C.
To improve traction
-
D.
To act as a brake
Correct answer: B.
Safety chains keep the trailer attached if the pintle hook fails.
Question 2 of 25 · Inspection
What's the impact of poor maintenance on doubles or triples?
-
A.
Increased risk of breakdowns and accidents
-
B.
Poor fuel efficiency
-
C.
Legal issues
-
D.
All of the above
Correct answer: D.
Poor maintenance leads to safety, efficiency, and legal problems.
Question 3 of 25 · Adverse Conditions
What's the safe way to handle a doubles or triples on a wet road?
-
A.
Reduce speed and increase following distance
-
B.
Drive at posted speed
-
C.
Use chains
-
D.
Both A and C
Correct answer: A.
Slower speeds and more space are essential on wet roads.
Question 4 of 25 · Vehicle Dynamics
What's the importance of "leverage" in doubles and triples?
-
A.
Each trailer affects the others; the rear can amplify or reduce stability
-
B.
It only affects fuel efficiency
-
C.
It doesn't matter
-
D.
It only affects loading
Correct answer: A.
Forces transfer between trailers; each one affects the stability of the combination.
Question 5 of 25 · Coupling
What's a common mistake when coupling doubles?
-
A.
Not properly aligning the dolly with the second trailer
-
B.
Forgetting to connect air lines
-
C.
Not testing the brakes
-
D.
All of the above
Correct answer: D.
Alignment, air lines, and brake tests are common areas for mistakes.
Question 6 of 25 · Coupling
What's the proper procedure for coupling a second trailer?
-
A.
Position the dolly under the second trailer, then back the lead trailer to the dolly
-
B.
Drive the lead trailer over the dolly
-
C.
Connect electrical first
-
D.
Lower the landing gear
Correct answer: A.
Position the dolly first, then back the lead trailer to it for proper coupling.
Question 7 of 25 · Inspection
When inspecting doubles and triples, what should you check?
-
A.
Each trailer's lights and brakes
-
B.
Each converter dolly
-
C.
Each fifth wheel and pintle hook
-
D.
All of the above
Correct answer: D.
Inspect every trailer, dolly, fifth wheel, and pintle hook before driving.
Question 8 of 25 · Coupling
How should you uncouple a converter dolly?
-
A.
Lower the dolly support, disconnect, and pull the tractor and first trailer away
-
B.
Disconnect and drive away
-
C.
Use the trailer parking brake
-
D.
Cut the air lines
Correct answer: A.
Lower support, disconnect lines and pin, then pull the lead unit away.
Question 9 of 25 · Inspection
Why must drivers inspect the dolly before connecting?
-
A.
To check for damage and proper operation
-
B.
To verify the brakes work
-
C.
To inspect the pintle hook
-
D.
All of the above
Correct answer: D.
Dolly inspection includes structure, brakes, and pintle hook condition.
Question 10 of 25 · Lane Changes
What's the major risk when changing lanes with doubles or triples?
-
A.
The rear trailer may not follow exactly
-
B.
Other vehicles may not see the long combination
-
C.
The trailer may swing out
-
D.
All of the above
Correct answer: D.
Visibility and rear-trailer tracking are both major lane-change risks.
Question 11 of 25 · Operation
What's the safest way to merge into traffic with doubles?
-
A.
Use turn signals early and merge gradually
-
B.
Speed up to merge quickly
-
C.
Force other drivers to yield
-
D.
Drive on the shoulder
Correct answer: A.
Signal early and merge gradually so other drivers can adjust.
Question 12 of 25 · Cargo
Doubles and triples are most stable when:
-
A.
All trailers are properly loaded
-
B.
Trailers are empty
-
C.
The lead trailer is empty
-
D.
The rear trailer is heaviest
Correct answer: A.
Proper loading on every trailer is key to stability.
Question 13 of 25 · Combination Air
What's the role of glad hands in doubles and triples?
-
A.
They connect air lines between each unit
-
B.
They are coupling devices
-
C.
They are safety chains
-
D.
They are landing gear
Correct answer: A.
Glad hands connect service and emergency air lines between every unit.
Question 14 of 25 · Speed Management
What's the safe speed for taking corners with doubles or triples?
-
A.
Posted speed limit
-
B.
Slower than single trailers
-
C.
Higher than single trailers
-
D.
No different from single trailers
Correct answer: B.
Take corners more slowly than single trailers due to greater rollover risk.
Question 15 of 25 · Coupling
How do you prevent a trailer from rolling away when uncoupled?
-
A.
Apply trailer brakes and chock the wheels
-
B.
Use the parking brake on the tractor
-
C.
Lower the landing gear quickly
-
D.
Drive away quickly
Correct answer: A.
Set trailer brakes and chock wheels to prevent any roll while uncoupling.
Question 16 of 25 · Mountain Driving
What's the recommended speed when descending a steep grade with doubles?
-
A.
Slow speed using lower gears and engine braking
-
B.
Posted speed limit
-
C.
Faster than single trailers
-
D.
Use service brakes only
Correct answer: A.
Use lower gears and engine braking. Service brakes only intermittently.
Question 17 of 25 · CDL Rules
Why are doubles and triples drivers required to have additional training?
-
A.
They handle differently and require more skill
-
B.
Federal regulations require training
-
C.
They have higher rollover risk
-
D.
All of the above
Correct answer: D.
Skill, regulation, and rollover risk all justify extra training.
Question 18 of 25 · Following Distance
What's the safe way to handle a doubles in heavy traffic?
-
A.
Maintain extra following distance and signal early
-
B.
Speed up to keep with traffic
-
C.
Use the shoulder
-
D.
Drive aggressively
Correct answer: A.
Extra space and early signals are critical in heavy traffic with combinations.
Question 19 of 25 · Vehicle Dynamics
Doubles and triples have ____ rollover risk than single trailers.
-
A.
Lower
-
B.
Higher
-
C.
The same
-
D.
No rollover risk
Correct answer: B.
Multiple trailers have higher rollover risk because of greater articulation and "crack-the-whip" effect.
Question 20 of 25 · Vehicle Dynamics
What is "crack-the-whip"?
-
A.
A driver discipline rule
-
B.
When the rear trailer swings out due to sudden steering inputs
-
C.
A type of weight distribution
-
D.
A coupling procedure
Correct answer: B.
The rear trailer can swing far wider than the tractor, magnifying steering inputs.
Question 21 of 25 · Coupling
What is the converter dolly?
-
A.
A type of tractor
-
B.
A coupling device used between trailers in doubles and triples
-
C.
A trailer brake
-
D.
A type of cargo
Correct answer: B.
The converter dolly connects two trailers in a combination set.
Question 22 of 25 · Backing
When backing doubles or triples, you should:
-
A.
Avoid backing if possible
-
B.
Use a helper as a spotter
-
C.
Back slowly and carefully
-
D.
All of the above
Correct answer: D.
Avoid backing combinations; use a spotter and go slowly when you must.
Question 23 of 25 · CDL Rules
Triples are illegal in many states because:
-
A.
They are too long and cause traffic disruption
-
B.
They have higher rollover risk
-
C.
They require special permits
-
D.
All of the above
Correct answer: D.
Many states prohibit triples due to length, rollover risk, and special permitting needs.
Question 24 of 25 · Coupling
What's a "spider" or "dolly converter"?
-
A.
A type of trailer
-
B.
A coupling device with a fifth wheel mounted on a single axle
-
C.
A type of brake
-
D.
A safety chain
Correct answer: B.
Converter dollies have a fifth wheel and an axle to allow connecting trailers.
Question 25 of 25 · Cargo
What's the impact of overloading a trailer in a doubles set?
-
A.
Increased rollover risk
-
B.
Poor handling
-
C.
Brake problems
-
D.
All of the above
Correct answer: D.
Overloading creates a chain of safety problems for the whole combination.
About the Doubles and Triples Test
The Doubles and Triples test covers pulling double and triple trailers, coupling and uncoupling, inspecting doubles and triples, antilock brake systems, and safe driving with multiple trailers. Doubles and triples are more likely to roll over than single trailers and are extremely sensitive to steering inputs at the rear trailer.
The Oregon Driver and Motor Vehicle Services administers this knowledge test as part of its commercial driver license program. To earn the Doubles/Triples (T) on your Oregon CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 7 questions
- Inspection: 3 questions
- Vehicle Dynamics: 3 questions
- Cargo: 2 questions
- CDL Rules: 2 questions
- Adverse Conditions: 1 question
- Lane Changes: 1 question
- Operation: 1 question
- Combination Air: 1 question
- Speed Management: 1 question
- Mountain Driving: 1 question
- Following Distance: 1 question
- Backing: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Oregon until you're ready for the official exam.
Tips specific to the Doubles and Triples test
Doubles and Triples questions emphasize the "crack-the-whip" effect, converter dolly inspection and use, pintle hooks, safety chains, the heaviest-trailer-first loading rule, and the higher rollover risk of multi-trailer combinations. Many states prohibit triples; check local rules.