25 realistic Combination Vehicles practice questions for Pennsylvania CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Inspection
Which is true about gladhand seals?
-
A.
They should be replaced if cracked or damaged
-
B.
They never need replacement
-
C.
They are the same as electrical connections
-
D.
They are always made of metal
Correct answer: A.
Replace damaged or worn rubber seals to keep air from leaking at the gladhands.
Question 2 of 25 · Skids
What should you do to recover from a trailer skid?
-
A.
Apply more brake pressure
-
B.
Release the brakes to allow trailer wheels to roll again
-
C.
Steer hard right
-
D.
Accelerate forward
Correct answer: B.
Release brakes to let trailer wheels roll, then steer to recover direction.
Question 3 of 25 · Vehicle Dynamics
Which of these is true about driving combination vehicles?
-
A.
They are easier to handle than single vehicles
-
B.
They are more likely to roll over and jackknife
-
C.
They use less fuel per mile
-
D.
They need fewer mirrors
Correct answer: B.
Combination vehicles require more skill and are more prone to rollovers and jackknives.
Question 4 of 25 · Coupling
What does a "low coupling" condition look like?
-
A.
Trailer is too high above the fifth wheel
-
B.
Trailer is at the right height
-
C.
Trailer is too low and tractor frame can hit the trailer
-
D.
Trailer is angled to the right
Correct answer: C.
A trailer too low can damage the tractor frame as it slides under it.
Question 5 of 25 · Skids
Which is the most common cause of trailer skid?
-
A.
Driving too fast for conditions
-
B.
Locking the rear trailer wheels by overbraking
-
C.
Worn brake shoes
-
D.
Too much trailer weight
Correct answer: B.
Trailer skids most often occur when rear trailer wheels lock during braking.
Question 6 of 25 · Coupling
When uncoupling, you should:
-
A.
Lower the landing gear before pulling the kingpin release
-
B.
Lift the trailer with the fifth wheel
-
C.
Release the parking brake
-
D.
Rev the engine
Correct answer: A.
Lower the landing gear so the trailer is supported before disconnecting the kingpin.
Question 7 of 25 · Cargo
Why is securement of cargo essential?
-
A.
To prevent the load from shifting
-
B.
To prevent injury to others
-
C.
To prevent damage to the vehicle
-
D.
All of the above
Correct answer: D.
Securement protects the load, prevents shifts that affect handling, and protects others.
Question 8 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
Question 9 of 25 · Inspection
Air leaks during pre-trip can be detected by:
-
A.
Listening for hissing
-
B.
Watching the air gauges drop
-
C.
Visually inspecting hoses and fittings
-
D.
All of the above
Correct answer: D.
Use multiple methods — listening, watching gauges, and visual inspection — to detect leaks.
Question 10 of 25 · Vehicle Dynamics
Empty trucks have what kind of stopping distance compared to fully loaded ones?
-
A.
Shorter
-
B.
Same
-
C.
Longer
-
D.
Half
Correct answer: C.
Empty rigs have less traction on drive axles and require greater stopping distance.
Question 11 of 25 · Coupling
What is the proper position for the fifth wheel?
-
A.
Tilted down toward the rear of the tractor with jaws open
-
B.
Pointed straight up
-
C.
Locked and ready
-
D.
Removed for inspection
Correct answer: A.
Before coupling, the fifth wheel should tilt down toward the rear with the jaws open.
Question 12 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 13 of 25 · Skids
What can cause a trailer skid in a combination vehicle?
-
A.
Locked trailer wheels and over-application of brakes
-
B.
Light loads on the trailer
-
C.
Tight steering at low speed
-
D.
High pressure in steering tires
Correct answer: A.
Locked trailer wheels cause trailer skid; reduce brake pressure to recover.
Question 14 of 25 · Inspection
When inspecting your trailer's wheels, what should you look for?
-
A.
Loose or missing nuts
-
B.
Cracked or broken wheel rims
-
C.
Bent or broken studs
-
D.
All of the above
Correct answer: D.
Inspect for loose nuts, cracks, bent studs, and other defects on every pre-trip.
Question 15 of 25 · Coupling
What is the kingpin?
-
A.
A pin in the engine
-
B.
A vertical pin on the front of the trailer that locks into the fifth wheel
-
C.
A part of the air brake system
-
D.
A type of warning device
Correct answer: B.
The kingpin slides into the fifth wheel jaws to lock the trailer to the tractor.
Question 16 of 25 · Coupling
When uncoupling, what is the final step?
-
A.
Lower the landing gear and disconnect electrical cord and air lines
-
B.
Drive forward immediately
-
C.
Set the parking brake on the tractor only
-
D.
Engage the trailer brakes only
Correct answer: A.
After raising the fifth wheel jaws and pulling forward, disconnect lines and lower landing gear.
Question 17 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 18 of 25 · Coupling
How can you keep a stiff coupling system from causing problems?
-
A.
Lubricate the fifth wheel
-
B.
Avoid backing under fast
-
C.
Inspect mounting bolts
-
D.
All of the above
Correct answer: D.
Lubricate, back slowly, and inspect mounting bolts to keep the coupling working safely.
Question 19 of 25 · Coupling
When coupling, what should you do after the fifth wheel locks onto the kingpin?
-
A.
Pull the tractor forward gently to make sure the kingpin is locked
-
B.
Disconnect the air lines
-
C.
Drive away immediately
-
D.
Release the trailer parking brake first
Correct answer: A.
Tug-test by gently pulling forward with the trailer brakes set to confirm the lock.
Question 20 of 25 · Vehicle Dynamics
Why should you avoid sudden steering and braking with combinations?
-
A.
It wears tires faster
-
B.
It can cause jackknife or rollover
-
C.
It uses more fuel
-
D.
It scares passengers
Correct answer: B.
Sudden inputs can break traction and lead to jackknifing or rollovers.
Question 21 of 25 · Combination Air
Trailer brakes are required to be:
-
A.
Adjusted properly and matched to tractor brakes
-
B.
Stronger than tractor brakes
-
C.
Disengaged on level roads
-
D.
Off when empty
Correct answer: A.
Trailer brakes must be in proper adjustment and balance with tractor brakes.
Question 22 of 25 · Operation
Which of these is most important when driving with a trailer?
-
A.
Use the engine retarder constantly
-
B.
Use proper braking and signaling
-
C.
Drive at maximum speed limits
-
D.
Skip pre-trip checks if running late
Correct answer: B.
Proper braking and clear signaling are essential to safe combination driving.
Question 23 of 25 · Combination Air
When the trailer breaks away or loses air pressure, the trailer brakes should:
-
A.
Release
-
B.
Apply automatically
-
C.
Vibrate
-
D.
Disengage
Correct answer: B.
A loss of air should automatically apply the trailer brakes via the emergency system.
Question 24 of 25 · Vehicle Dynamics
When you turn suddenly with a high center of gravity, the trailer can:
-
A.
Roll over
-
B.
Stop more quickly
-
C.
Track better
-
D.
Reduce fuel use
Correct answer: A.
High centers of gravity make trailers prone to rollover during sharp turns.
Question 25 of 25 · Inspection
Which of these is not a part of the trailer's electrical system?
-
A.
Lights
-
B.
Brake control
-
C.
Power line cord (pigtail)
-
D.
Hydraulic pump
Correct answer: D.
Hydraulic pumps are not part of standard trailer electrical systems on highway combinations.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Pennsylvania Department of Transportation — Driver Services administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Pennsylvania CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 9 questions
- Vehicle Dynamics: 5 questions
- Inspection: 4 questions
- Skids: 3 questions
- Combination Air: 2 questions
- Cargo: 1 question
- Operation: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Pennsylvania until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.