25 realistic Combination Vehicles practice questions for Rhode Island CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 2 of 25 · Coupling
What does a "low coupling" condition look like?
-
A.
Trailer is too high above the fifth wheel
-
B.
Trailer is at the right height
-
C.
Trailer is too low and tractor frame can hit the trailer
-
D.
Trailer is angled to the right
Correct answer: C.
A trailer too low can damage the tractor frame as it slides under it.
Question 3 of 25 · Combination Air
What should the tractor protection valve do?
-
A.
Keep tractor air supply if trailer breaks away or develops a major leak
-
B.
Set the trailer parking brake on a hill
-
C.
Apply trailer brakes during a normal stop
-
D.
Disconnect the trailer
Correct answer: A.
It protects the tractor air supply by closing if a major air loss occurs.
Question 4 of 25 · Coupling
When uncoupling, you should:
-
A.
Lower the landing gear before pulling the kingpin release
-
B.
Lift the trailer with the fifth wheel
-
C.
Release the parking brake
-
D.
Rev the engine
Correct answer: A.
Lower the landing gear so the trailer is supported before disconnecting the kingpin.
Question 5 of 25 · Vehicle Dynamics
Off-tracking is most pronounced in:
-
A.
Single vehicles
-
B.
Long combinations and curves
-
C.
Empty trailers
-
D.
Vehicles with disc brakes
Correct answer: B.
Longer wheelbases and tighter curves cause greater off-tracking.
Question 6 of 25 · Following Distance
What is "rear-end collision" risk for combination vehicles?
-
A.
It is reduced when carrying long cargo
-
B.
They have a higher risk because of long stopping distances and rear blind spots
-
C.
They have no greater risk
-
D.
Only for empty rigs
Correct answer: B.
Long stopping distance and rear blind spots increase rear-end collision risk.
Question 7 of 25 · Combination Air
What is glad hands?
-
A.
Trailer doors
-
B.
Couplers used to join air lines from the tractor to the trailer
-
C.
Mirror brackets
-
D.
Brake levers
Correct answer: B.
Glad hands connect the service and emergency air lines between tractor and trailer.
Question 8 of 25 · Operation
Which of these is most important when driving with a trailer?
-
A.
Use the engine retarder constantly
-
B.
Use proper braking and signaling
-
C.
Drive at maximum speed limits
-
D.
Skip pre-trip checks if running late
Correct answer: B.
Proper braking and clear signaling are essential to safe combination driving.
Question 9 of 25 · Skids
How can you correct a tractor jackknife?
-
A.
Apply the brakes harder
-
B.
Steer in the direction of the skid and accelerate gently
-
C.
Stop steering input
-
D.
Release the brakes and counter-steer
Correct answer: D.
Release the brakes to regain traction; counter-steer carefully to recover.
Question 10 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
Question 11 of 25 · Speed Management
What is the most common cause of fatal crashes for combination vehicles?
-
A.
Loss of control due to speed too fast for conditions
-
B.
Engine failure
-
C.
Tire blowouts
-
D.
Mechanical defects only
Correct answer: A.
Driving too fast for conditions is the leading cause of serious crashes.
Question 12 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 13 of 25 · Inspection
When inspecting your trailer's wheels, what should you look for?
-
A.
Loose or missing nuts
-
B.
Cracked or broken wheel rims
-
C.
Bent or broken studs
-
D.
All of the above
Correct answer: D.
Inspect for loose nuts, cracks, bent studs, and other defects on every pre-trip.
Question 14 of 25 · Backing
Which is correct about backing a tractor-trailer?
-
A.
Steer in the same direction you want the trailer to go
-
B.
Steer in the opposite direction you want the trailer to go
-
C.
Use the throttle to back
-
D.
Back as fast as possible
Correct answer: B.
When backing, turn the steering wheel opposite to the direction you want the trailer to move.
Question 15 of 25 · Cargo
How do you know the trailer is properly loaded?
-
A.
Cargo is centered, balanced, and properly secured
-
B.
Cargo extends beyond the trailer ends
-
C.
Cargo is stacked unevenly
-
D.
Cargo is on top of the cab
Correct answer: A.
Centered, balanced, and secured loads handle predictably.
Question 16 of 25 · Skids
Tractor jackknife occurs when:
-
A.
Drive wheels lose traction and skid
-
B.
The trailer wheels lock
-
C.
The trailer slides forward
-
D.
Steering wheels lock
Correct answer: A.
Drive wheels skidding cause tractor jackknife; trailer wheels skidding cause trailer jackknife.
Question 17 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 18 of 25 · Coupling
When coupling, what should you do after the fifth wheel locks onto the kingpin?
-
A.
Pull the tractor forward gently to make sure the kingpin is locked
-
B.
Disconnect the air lines
-
C.
Drive away immediately
-
D.
Release the trailer parking brake first
Correct answer: A.
Tug-test by gently pulling forward with the trailer brakes set to confirm the lock.
Question 19 of 25 · Skids
How can drivers avoid jackknifing?
-
A.
Brake gently and look ahead
-
B.
Adjust speed for road and weather
-
C.
Use ABS where equipped
-
D.
All of the above
Correct answer: D.
Smooth braking, appropriate speed, and ABS all reduce jackknife risk.
Question 20 of 25 · Vehicle Dynamics
Which of these is true about driving combination vehicles?
-
A.
They are easier to handle than single vehicles
-
B.
They are more likely to roll over and jackknife
-
C.
They use less fuel per mile
-
D.
They need fewer mirrors
Correct answer: B.
Combination vehicles require more skill and are more prone to rollovers and jackknives.
Question 21 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 22 of 25 · Skids
What is the result of a "trailer jackknife"?
-
A.
Trailer continues straight ahead
-
B.
Trailer swings out and tractor pivots
-
C.
Trailer comes to a quick safe stop
-
D.
Trailer disengages
Correct answer: B.
In a trailer jackknife, the trailer swings out, often into adjacent lanes.
Question 23 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
Question 24 of 25 · Coupling
You should NEVER:
-
A.
Back under a trailer at an angle
-
B.
Inspect the fifth wheel
-
C.
Use the parking brake
-
D.
Tug-test the kingpin
Correct answer: A.
Backing at an angle can damage the kingpin or push the trailer sideways.
Question 25 of 25 · Vehicle Dynamics
Empty trucks have what kind of stopping distance compared to fully loaded ones?
-
A.
Shorter
-
B.
Same
-
C.
Longer
-
D.
Half
Correct answer: C.
Empty rigs have less traction on drive axles and require greater stopping distance.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Rhode Island Division of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Rhode Island CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 7 questions
- Vehicle Dynamics: 5 questions
- Skids: 5 questions
- Combination Air: 2 questions
- Following Distance: 1 question
- Operation: 1 question
- Speed Management: 1 question
- Inspection: 1 question
- Backing: 1 question
- Cargo: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Rhode Island until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.