25 realistic Combination Vehicles practice questions for Arizona CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Inspection
What is the proper way to test the parking brakes after coupling?
-
A.
Apply trailer parking brake and try to gently pull forward
-
B.
Drive at normal speed
-
C.
Apply foot brake repeatedly
-
D.
Disconnect glad hands
Correct answer: A.
A gentle pull forward with parking brakes set confirms holding power.
Question 2 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 3 of 25 · Inspection
Air leaks during pre-trip can be detected by:
-
A.
Listening for hissing
-
B.
Watching the air gauges drop
-
C.
Visually inspecting hoses and fittings
-
D.
All of the above
Correct answer: D.
Use multiple methods — listening, watching gauges, and visual inspection — to detect leaks.
Question 4 of 25 · Coupling
You should NEVER:
-
A.
Back under a trailer at an angle
-
B.
Inspect the fifth wheel
-
C.
Use the parking brake
-
D.
Tug-test the kingpin
Correct answer: A.
Backing at an angle can damage the kingpin or push the trailer sideways.
Question 5 of 25 · Vehicle Dynamics
Empty trucks have what kind of stopping distance compared to fully loaded ones?
-
A.
Shorter
-
B.
Same
-
C.
Longer
-
D.
Half
Correct answer: C.
Empty rigs have less traction on drive axles and require greater stopping distance.
Question 6 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 7 of 25 · Inspection
When checking the trailer air supply, you should:
-
A.
Charge the trailer with air, then disconnect the supply hose to test trailer emergency brakes
-
B.
Pump the brakes
-
C.
Disconnect the trailer power cord
-
D.
Open the trailer service line manually
Correct answer: A.
Disconnecting the supply line tests that the trailer emergency brakes apply automatically.
Question 8 of 25 · CDL Rules
Which is true about long combination vehicles (LCVs)?
-
A.
They are easier to maneuver in tight spaces
-
B.
They require additional driver training and special permits
-
C.
They handle the same as single trailers
-
D.
They never require special routes
Correct answer: B.
LCVs need extra training, certifications, and often follow restricted routes.
Question 9 of 25 · Coupling
What does a "low coupling" condition look like?
-
A.
Trailer is too high above the fifth wheel
-
B.
Trailer is at the right height
-
C.
Trailer is too low and tractor frame can hit the trailer
-
D.
Trailer is angled to the right
Correct answer: C.
A trailer too low can damage the tractor frame as it slides under it.
Question 10 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
Question 11 of 25 · Bobtail
What happens if you bobtail (no trailer) and brake hard?
-
A.
You stop more quickly than loaded
-
B.
Drive wheels can lock and skid because there is little weight on them
-
C.
Vehicle handles like a loaded truck
-
D.
No special concerns
Correct answer: B.
Bobtailing leaves little weight on drive axles, increasing skid risk under hard braking.
Question 12 of 25 · Inspection
You should inspect the rear of the trailer for:
-
A.
Cracked or missing lights
-
B.
Lights and reflectors are clean and operational
-
C.
Mud flap condition
-
D.
All of the above
Correct answer: D.
Check lights, reflectors, mud flaps, and license plate during pre-trip.
Question 13 of 25 · Following Distance
What is "rear-end collision" risk for combination vehicles?
-
A.
It is reduced when carrying long cargo
-
B.
They have a higher risk because of long stopping distances and rear blind spots
-
C.
They have no greater risk
-
D.
Only for empty rigs
Correct answer: B.
Long stopping distance and rear blind spots increase rear-end collision risk.
Question 14 of 25 · Coupling
How can you keep a stiff coupling system from causing problems?
-
A.
Lubricate the fifth wheel
-
B.
Avoid backing under fast
-
C.
Inspect mounting bolts
-
D.
All of the above
Correct answer: D.
Lubricate, back slowly, and inspect mounting bolts to keep the coupling working safely.
Question 15 of 25 · Backing
Which is correct about backing a tractor-trailer?
-
A.
Steer in the same direction you want the trailer to go
-
B.
Steer in the opposite direction you want the trailer to go
-
C.
Use the throttle to back
-
D.
Back as fast as possible
Correct answer: B.
When backing, turn the steering wheel opposite to the direction you want the trailer to move.
Question 16 of 25 · Inspection
Which is true about gladhand seals?
-
A.
They should be replaced if cracked or damaged
-
B.
They never need replacement
-
C.
They are the same as electrical connections
-
D.
They are always made of metal
Correct answer: A.
Replace damaged or worn rubber seals to keep air from leaking at the gladhands.
Question 17 of 25 · Vehicle Dynamics
Which of these is true about driving combination vehicles?
-
A.
They are easier to handle than single vehicles
-
B.
They are more likely to roll over and jackknife
-
C.
They use less fuel per mile
-
D.
They need fewer mirrors
Correct answer: B.
Combination vehicles require more skill and are more prone to rollovers and jackknives.
Question 18 of 25 · Skids
Which is the most common cause of trailer skid?
-
A.
Driving too fast for conditions
-
B.
Locking the rear trailer wheels by overbraking
-
C.
Worn brake shoes
-
D.
Too much trailer weight
Correct answer: B.
Trailer skids most often occur when rear trailer wheels lock during braking.
Question 19 of 25 · Skids
What is the result of a "trailer jackknife"?
-
A.
Trailer continues straight ahead
-
B.
Trailer swings out and tractor pivots
-
C.
Trailer comes to a quick safe stop
-
D.
Trailer disengages
Correct answer: B.
In a trailer jackknife, the trailer swings out, often into adjacent lanes.
Question 20 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 21 of 25 · Combination Air
Trailer hand valve is used to:
-
A.
Test trailer brakes
-
B.
Park the trailer
-
C.
Bypass the foot valve
-
D.
Drain trailer tanks
Correct answer: A.
Use the trailer hand valve only for testing — not for parking or normal stops.
Question 22 of 25 · Combination Air
Trailer brakes are required to be:
-
A.
Adjusted properly and matched to tractor brakes
-
B.
Stronger than tractor brakes
-
C.
Disengaged on level roads
-
D.
Off when empty
Correct answer: A.
Trailer brakes must be in proper adjustment and balance with tractor brakes.
Question 23 of 25 · Inspection
When should you check trailer brakes during operation?
-
A.
First few miles after coupling
-
B.
Every fuel stop
-
C.
Just at the end of the trip
-
D.
Never during the trip
Correct answer: A.
Test trailer brakes early in the trip to make sure they are functioning correctly.
Question 24 of 25 · Combination Air
When the trailer breaks away or loses air pressure, the trailer brakes should:
-
A.
Release
-
B.
Apply automatically
-
C.
Vibrate
-
D.
Disengage
Correct answer: B.
A loss of air should automatically apply the trailer brakes via the emergency system.
Question 25 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Arizona Motor Vehicle Division administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Arizona CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Inspection: 6 questions
- Coupling: 6 questions
- Vehicle Dynamics: 4 questions
- Combination Air: 3 questions
- Skids: 2 questions
- CDL Rules: 1 question
- Bobtail: 1 question
- Following Distance: 1 question
- Backing: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Arizona until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.