25 realistic Air Brakes practice questions for Delaware CDL applicants. Required for: Vehicles equipped with air brake systems. Official test: 25 questions, 20 correct to pass.
Question 1 of 25 · Parking
When parking a tractor-trailer with spring brakes:
-
A.
Use the trailer hand valve only
-
B.
Use the parking brake only — do not push the brake pedal down to hold the vehicle
-
C.
Press the foot brake and then engage the parking brake
-
D.
Set both brakes simultaneously
Correct answer: B.
Don't push the pedal down because it will cause damage. Set the parking brakes only.
Question 2 of 25 · Gauges
You should know your vehicle is properly equipped with which gauge?
-
A.
Two air pressure gauges (or one with two needles) showing pressure in primary and secondary tanks
-
B.
A vacuum gauge
-
C.
A voltage meter only
-
D.
A coolant gauge only
Correct answer: A.
Dual air systems require gauges for both primary and secondary air supplies.
Question 3 of 25 · Operation
When making a normal stop, what should you do?
-
A.
Push the brake pedal down so you can stop at a safe place and remain in control
-
B.
Pump the brakes
-
C.
Use only the parking brake
-
D.
Use only the trailer hand valve
Correct answer: A.
Apply pressure progressively to come to a smooth, safe stop while maintaining control.
Question 4 of 25 · Speed Management
Brake fade results from:
-
A.
Oversized brakes
-
B.
Excessive heat from prolonged braking
-
C.
Too much air pressure
-
D.
Cold weather
Correct answer: B.
Brake fade is caused by overheating brakes that lose stopping power.
Question 5 of 25 · Parking
On a tractor with no trailer attached, the tractor parking brake control:
-
A.
Will lock and unlock the front brakes
-
B.
Will set or release the spring brakes on the tractor
-
C.
Has no function
-
D.
Operates only the trailer brakes
Correct answer: B.
The yellow diamond control sets and releases the tractor parking (spring) brakes.
Question 6 of 25 · System Basics
Which of the following is NOT in the air brake system?
-
A.
Brake chambers
-
B.
Slack adjusters
-
C.
S-cam
-
D.
Hydraulic master cylinder
Correct answer: D.
Hydraulic master cylinders are part of hydraulic systems, not air brake systems.
Question 7 of 25 · Compressor
Brake-system air pressure should build from 85 to 100 psi within:
-
A.
15 seconds in dual systems
-
B.
30 seconds in dual systems
-
C.
45 seconds in dual systems
-
D.
60 seconds in dual systems
Correct answer: C.
Build-up time should be within 45 seconds in dual air systems.
Question 8 of 25 · Compressor
What is the purpose of a one-way check valve?
-
A.
Allow air to flow in one direction
-
B.
Allow water to drain
-
C.
Prevent the trailer from moving
-
D.
Increase pressure in the supply tank
Correct answer: A.
It permits airflow in one direction only — protecting the system if the compressor fails.
Question 9 of 25 · Inspection
How much air pressure (psi) loss is allowed per minute for combination vehicles with the engine off and brakes released?
-
A.
Up to 1 psi
-
B.
Up to 2 psi
-
C.
Up to 3 psi
-
D.
Up to 4 psi
Correct answer: B.
Combination vehicles allow up to 3 psi loss per minute with brakes released; with brakes applied, up to 4 psi.
Question 10 of 25 · Inspection
When should you check the parking brake?
-
A.
Whenever you start a trip
-
B.
Once a month
-
C.
Only at inspections
-
D.
When the brake warning light is on
Correct answer: A.
Test the parking brake every trip — apply the brake and try to move forward gently.
Question 11 of 25 · Operation
When the brake pedal is pushed harder, what happens?
-
A.
Brake pedal must be pumped to release
-
B.
More air goes to the brakes; less foot pressure releases air
-
C.
It locks the brakes permanently
-
D.
The brakes do not respond
Correct answer: B.
The harder you push, the more air pressure is sent to the brake chambers.
Question 12 of 25 · Parking
Why should you use chocks?
-
A.
When parking on a hill
-
B.
On level ground when leaving the vehicle
-
C.
Whenever brakes might fail or it's required by company policy or law
-
D.
All of the above
Correct answer: D.
Chocks should be used when required to prevent vehicle movement.
Question 13 of 25 · Combination Air
When should the trailer brake hand valve be used?
-
A.
To park the trailer
-
B.
To test the trailer brakes only
-
C.
To stop the entire combination
-
D.
Never to keep the vehicle from rolling
Correct answer: B.
Use it only to test trailer brakes. Never use it to park or as a service brake during normal stops.
Question 14 of 25 · Inspection
How much air pressure (psi) loss is allowed per minute for single vehicles with the engine off and brakes released?
-
A.
Up to 1 psi
-
B.
Up to 2 psi
-
C.
Up to 3 psi
-
D.
Up to 4 psi
Correct answer: B.
Single vehicles allow up to 2 psi per minute with brakes released; up to 3 psi with brakes applied.
Question 15 of 25 · Spring Brakes
What does a "spring brake" mean?
-
A.
A brake that operates only in spring weather
-
B.
A mechanical brake that uses powerful springs to apply the brake when air pressure is lost
-
C.
A specific kind of disc brake
-
D.
A backup hydraulic brake
Correct answer: B.
Spring brakes use powerful coil springs to apply the brakes when air pressure is lost.
Question 16 of 25 · Tanks
Air brake equipped vehicles must have:
-
A.
Only an emergency brake
-
B.
A drain valve in each air tank
-
C.
Hydraulic backup
-
D.
Disc brakes only
Correct answer: B.
Each air tank has a drain valve to remove water and oil that collect in the tank.
Question 17 of 25 · Inspection
When checking air brake adjustment, the engine should be:
-
A.
Running at idle
-
B.
Off with the brakes released
-
C.
Running at high RPM
-
D.
Off with the brakes applied
Correct answer: B.
Inspect with the engine off and the brakes released so chambers are not pressurized.
Question 18 of 25 · ABS
What is the proper procedure for an air brake stop in a vehicle equipped with ABS?
-
A.
Pump the brakes
-
B.
Press the brake pedal firmly and steadily; let ABS work
-
C.
Disengage ABS first
-
D.
Apply the parking brake
Correct answer: B.
With ABS, brake firmly and steadily. ABS prevents wheel lockup automatically.
Question 19 of 25 · System Basics
Air brake systems combine three different braking systems. They are:
-
A.
Service, parking, and emergency brakes
-
B.
Hydraulic, parking, and emergency brakes
-
C.
Front, rear, and trailer brakes
-
D.
Disc, drum, and parking brakes
Correct answer: A.
The three are: the service brake, the parking brake, and the emergency brake.
Question 20 of 25 · Combination Air
What component prevents air pressure loss in case of a leak between the tractor and trailer?
-
A.
Tractor protection valve
-
B.
Air dryer
-
C.
Foot brake valve
-
D.
Modulating valve
Correct answer: A.
The tractor protection valve closes off the trailer air supply during a leak, protecting tractor air.
Question 21 of 25 · Combination Air
What does the trailer hand valve do?
-
A.
Operates only the trailer brakes
-
B.
Operates both the tractor and trailer brakes
-
C.
Engages the parking brakes
-
D.
Lowers the landing gear
Correct answer: A.
The hand valve (trolley valve) controls only the trailer service brakes.
Question 22 of 25 · Foundation Brakes
When checking the slack adjuster on S-cam brakes, the slack adjuster should not move more than:
-
A.
1/2 inch
-
B.
1 inch
-
C.
About 1 inch where the push rod attaches to it
-
D.
2 inches
Correct answer: C.
When pulled by hand, the slack adjuster shouldn't move more than about an inch where the push rod attaches.
Question 23 of 25 · Inspection
What is the air loss rate for combination vehicles with brakes applied?
-
A.
1 psi per minute
-
B.
2 psi per minute
-
C.
3 psi per minute
-
D.
4 psi per minute
Correct answer: D.
Combination vehicles can lose up to 4 psi per minute with brakes applied.
Question 24 of 25 · Emergency Maneuvers
Which of these statements is true about emergency braking?
-
A.
Pumping the brakes is always best
-
B.
Stab braking is for non-ABS vehicles in emergencies
-
C.
You should brake harder than necessary
-
D.
Stab braking is the same as pumping
Correct answer: B.
Stab braking applies to non-ABS systems: full application until lockup, then release.
Question 25 of 25 · Speed Management
Air brake lag is:
-
A.
The time required for the brakes to apply after the pedal is pressed
-
B.
The amount of free play in the brake pedal
-
C.
The distance traveled before the brakes release
-
D.
The time to drain air tanks
Correct answer: A.
Lag is the time between pressing the pedal and the brakes actually applying — about 0.4 seconds.
About the Air Brakes Test
The Air Brakes test covers air brake system parts (compressor, governor, reservoirs, drain valves, alcohol evaporator, safety valve, brake pedal, foundation brakes), dual air brake systems, inspecting air brakes, using air brakes (normal stops, emergency stops, parking brakes), and proper procedures for braking on downgrades. If you fail or skip the Air Brakes test, your CDL is restricted to vehicles without full air brake systems.
The Delaware Division of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Air Brakes Endorsement on your Delaware CDL, you need to score at least 20 out of 25 on the official version.
Topics covered on this practice test
- Inspection: 5 questions
- Parking: 3 questions
- Combination Air: 3 questions
- Operation: 2 questions
- Speed Management: 2 questions
- System Basics: 2 questions
- Compressor: 2 questions
- Gauges: 1 question
- Spring Brakes: 1 question
- Tanks: 1 question
- ABS: 1 question
- Foundation Brakes: 1 question
- Emergency Maneuvers: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Delaware until you're ready for the official exam.
Tips specific to the Air Brakes test
Air Brakes questions test your ability to identify components, follow inspection sequences, and respond to system failures. Memorize the cut-in and cut-out pressures, the low-pressure warning thresholds, the pressure ranges at which spring brakes apply, and the maximum allowable air-loss rates. Many questions have nearly-identical wording, so precision matters.