25 realistic Air Brakes practice questions for Maryland CDL applicants. Required for: Vehicles equipped with air brake systems. Official test: 25 questions, 20 correct to pass.
Question 1 of 25 · Inspection
How can you check the slack adjusters?
-
A.
Pull hard on each slack adjuster — they should not move more than about 1 inch
-
B.
Listen for air leaks at each chamber
-
C.
Watch the brake light flash
-
D.
Look at the brake pedal travel
Correct answer: A.
Pulling hard, slack adjusters should not move more than about 1 inch where the push rod attaches.
Question 2 of 25 · Spring Brakes
What happens if the air pressure drops to between 20 and 45 psi?
-
A.
Nothing happens
-
B.
The compressor cuts in
-
C.
Spring brakes apply automatically
-
D.
The trailer is released
Correct answer: C.
Spring brakes typically apply automatically in this range, stopping the vehicle.
Question 3 of 25 · Speed Management
Why is it important not to over-apply the brakes?
-
A.
Brakes can overheat and fade
-
B.
Brakes will lock and skid
-
C.
You may lose control of the vehicle
-
D.
All of the above
Correct answer: D.
Over-application leads to fade, lockup, skidding, and loss of control.
Question 4 of 25 · Operation
When the brake pedal is pushed harder, what happens?
-
A.
Brake pedal must be pumped to release
-
B.
More air goes to the brakes; less foot pressure releases air
-
C.
It locks the brakes permanently
-
D.
The brakes do not respond
Correct answer: B.
The harder you push, the more air pressure is sent to the brake chambers.
Question 5 of 25 · System Basics
Air brakes use compressed air to:
-
A.
Lubricate the wheels
-
B.
Make the brakes work
-
C.
Cool the engine
-
D.
Increase fuel pressure
Correct answer: B.
Compressed air is the working fluid that applies the brakes in an air brake system.
Question 6 of 25 · Inspection
How much air pressure (psi) loss is allowed per minute for combination vehicles with the engine off and brakes released?
-
A.
Up to 1 psi
-
B.
Up to 2 psi
-
C.
Up to 3 psi
-
D.
Up to 4 psi
Correct answer: B.
Combination vehicles allow up to 3 psi loss per minute with brakes released; with brakes applied, up to 4 psi.
Question 7 of 25 · Speed Management
Air brake lag distance at 55 mph on dry pavement adds about:
-
A.
12 feet to stopping distance
-
B.
32 feet to stopping distance
-
C.
50 feet to stopping distance
-
D.
100 feet to stopping distance
Correct answer: B.
Air brake systems have a lag of about 0.4 seconds, adding roughly 32 feet at 55 mph.
Question 8 of 25 · Compressor
What is the purpose of a one-way check valve?
-
A.
Allow air to flow in one direction
-
B.
Allow water to drain
-
C.
Prevent the trailer from moving
-
D.
Increase pressure in the supply tank
Correct answer: A.
It permits airflow in one direction only — protecting the system if the compressor fails.
Question 9 of 25 · ABS
If the ABS warning light comes on, you should:
-
A.
Stop driving immediately
-
B.
Continue, knowing brakes still work — but ABS may not
-
C.
Pump the brakes constantly
-
D.
Engage the trailer hand valve
Correct answer: B.
You still have normal braking; only the ABS function may be off. Get it fixed soon.
Question 10 of 25 · Foundation Brakes
When checking the slack adjuster on S-cam brakes, the slack adjuster should not move more than:
-
A.
1/2 inch
-
B.
1 inch
-
C.
About 1 inch where the push rod attaches to it
-
D.
2 inches
Correct answer: C.
When pulled by hand, the slack adjuster shouldn't move more than about an inch where the push rod attaches.
Question 11 of 25 · Spring Brakes
Spring brakes will come on automatically when air pressure drops to:
-
A.
100 psi
-
B.
60 psi or less
-
C.
20 to 45 psi
-
D.
10 psi
Correct answer: C.
Spring brakes typically apply automatically between 20 and 45 psi.
Question 12 of 25 · Combination Air
When should the trailer brake hand valve be used?
-
A.
To park the trailer
-
B.
To test the trailer brakes only
-
C.
To stop the entire combination
-
D.
Never to keep the vehicle from rolling
Correct answer: B.
Use it only to test trailer brakes. Never use it to park or as a service brake during normal stops.
Question 13 of 25 · Tanks
What is the safety valve set to open at?
-
A.
100 psi
-
B.
125 psi
-
C.
150 psi
-
D.
180 psi
Correct answer: C.
The safety valve is normally set to open at 150 psi to protect the system from over-pressurization.
Question 14 of 25 · Compressor
If the air compressor governor is not working properly:
-
A.
Air compressor may not maintain enough pressure to safely operate the brakes
-
B.
The brakes will work harder
-
C.
Brakes may not release at all
-
D.
There is no impact on safety
Correct answer: A.
A faulty governor can cause low system pressure or over-pressurization, both unsafe.
Question 15 of 25 · Inspection
How do you test the low pressure warning signal?
-
A.
With the engine off, pump the brake pedal until the signal activates (must come on at 60 psi or above)
-
B.
Drive the vehicle to lose pressure
-
C.
Open the air tank drain valve briefly
-
D.
Push the parking brake control
Correct answer: A.
Pump the brake to lower pressure; warning must come on at 60 psi or higher.
Question 16 of 25 · Inspection
What is the air loss rate for combination vehicles with brakes applied?
-
A.
1 psi per minute
-
B.
2 psi per minute
-
C.
3 psi per minute
-
D.
4 psi per minute
Correct answer: D.
Combination vehicles can lose up to 4 psi per minute with brakes applied.
Question 17 of 25 · Compressor
Brake-system air pressure should build from 85 to 100 psi within:
-
A.
15 seconds in dual systems
-
B.
30 seconds in dual systems
-
C.
45 seconds in dual systems
-
D.
60 seconds in dual systems
Correct answer: C.
Build-up time should be within 45 seconds in dual air systems.
Question 18 of 25 · Gauges
What gauge tells you the air pressure being delivered to the brakes?
-
A.
Application pressure gauge
-
B.
Supply pressure gauge
-
C.
Speedometer
-
D.
Tachometer
Correct answer: A.
The application gauge shows pressure being applied to the brakes when the pedal is pressed.
Question 19 of 25 · Inspection
When should you push the brake pedal during the air brake test?
-
A.
Only when the engine is running
-
B.
When checking the compressor
-
C.
When the engine is off, to check that pressure does not drop too quickly
-
D.
During the brake light test only
Correct answer: C.
Apply firm pressure with the engine off to check for excessive air leakage from the system.
Question 20 of 25 · Foundation Brakes
Brake drums (or discs) must not have cracks longer than:
-
A.
1/4 the width of the friction area
-
B.
1/2 the width of the friction area
-
C.
3/4 the width of the friction area
-
D.
Anything is acceptable
Correct answer: B.
Cracks longer than one-half the width of the friction area are a safety violation.
Question 21 of 25 · Tanks
When should you drain the air tanks?
-
A.
Once a week
-
B.
Only when the warning light is on
-
C.
At the end of each working day
-
D.
Once a month
Correct answer: C.
Drain tanks completely at the end of each working day to remove water and oil.
Question 22 of 25 · Compressor
The air compressor governor controls:
-
A.
When the air compressor will pump air into the storage tanks
-
B.
When the brakes are applied
-
C.
When emergency brakes engage
-
D.
How fast the air compressor turns
Correct answer: A.
The governor cuts the compressor in and out to keep the system within its operating pressure range.
Question 23 of 25 · Emergency Maneuvers
Which of these statements is true about emergency braking?
-
A.
Pumping the brakes is always best
-
B.
Stab braking is for non-ABS vehicles in emergencies
-
C.
You should brake harder than necessary
-
D.
Stab braking is the same as pumping
Correct answer: B.
Stab braking applies to non-ABS systems: full application until lockup, then release.
Question 24 of 25 · Operation
When making a normal stop, what should you do?
-
A.
Push the brake pedal down so you can stop at a safe place and remain in control
-
B.
Pump the brakes
-
C.
Use only the parking brake
-
D.
Use only the trailer hand valve
Correct answer: A.
Apply pressure progressively to come to a smooth, safe stop while maintaining control.
Question 25 of 25 · Emergency Maneuvers
Stab braking includes which of these steps?
-
A.
Apply brakes fully, release when wheels lock, reapply when wheels begin rolling
-
B.
Apply brakes lightly until they fade
-
C.
Pump the brakes rapidly
-
D.
Apply the parking brake repeatedly
Correct answer: A.
Stab braking: full application, release on lockup, reapply when wheels turn again.
About the Air Brakes Test
The Air Brakes test covers air brake system parts (compressor, governor, reservoirs, drain valves, alcohol evaporator, safety valve, brake pedal, foundation brakes), dual air brake systems, inspecting air brakes, using air brakes (normal stops, emergency stops, parking brakes), and proper procedures for braking on downgrades. If you fail or skip the Air Brakes test, your CDL is restricted to vehicles without full air brake systems.
The Maryland Motor Vehicle Administration administers this knowledge test as part of its commercial driver license program. To earn the Air Brakes Endorsement on your Maryland CDL, you need to score at least 20 out of 25 on the official version.
Topics covered on this practice test
- Inspection: 5 questions
- Compressor: 4 questions
- Spring Brakes: 2 questions
- Speed Management: 2 questions
- Operation: 2 questions
- Foundation Brakes: 2 questions
- Tanks: 2 questions
- Emergency Maneuvers: 2 questions
- System Basics: 1 question
- ABS: 1 question
- Combination Air: 1 question
- Gauges: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Maryland until you're ready for the official exam.
Tips specific to the Air Brakes test
Air Brakes questions test your ability to identify components, follow inspection sequences, and respond to system failures. Memorize the cut-in and cut-out pressures, the low-pressure warning thresholds, the pressure ranges at which spring brakes apply, and the maximum allowable air-loss rates. Many questions have nearly-identical wording, so precision matters.