25 realistic Combination Vehicles practice questions for New York CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Skids
Which is the most common cause of trailer skid?
-
A.
Driving too fast for conditions
-
B.
Locking the rear trailer wheels by overbraking
-
C.
Worn brake shoes
-
D.
Too much trailer weight
Correct answer: B.
Trailer skids most often occur when rear trailer wheels lock during braking.
Question 2 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 3 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 4 of 25 · Combination Air
When the trailer breaks away or loses air pressure, the trailer brakes should:
-
A.
Release
-
B.
Apply automatically
-
C.
Vibrate
-
D.
Disengage
Correct answer: B.
A loss of air should automatically apply the trailer brakes via the emergency system.
Question 5 of 25 · Following Distance
What is "rear-end collision" risk for combination vehicles?
-
A.
It is reduced when carrying long cargo
-
B.
They have a higher risk because of long stopping distances and rear blind spots
-
C.
They have no greater risk
-
D.
Only for empty rigs
Correct answer: B.
Long stopping distance and rear blind spots increase rear-end collision risk.
Question 6 of 25 · Skids
What can cause a trailer skid in a combination vehicle?
-
A.
Locked trailer wheels and over-application of brakes
-
B.
Light loads on the trailer
-
C.
Tight steering at low speed
-
D.
High pressure in steering tires
Correct answer: A.
Locked trailer wheels cause trailer skid; reduce brake pressure to recover.
Question 7 of 25 · Inspection
Which is true about gladhand seals?
-
A.
They should be replaced if cracked or damaged
-
B.
They never need replacement
-
C.
They are the same as electrical connections
-
D.
They are always made of metal
Correct answer: A.
Replace damaged or worn rubber seals to keep air from leaking at the gladhands.
Question 8 of 25 · Cargo
What can cause a high center of gravity?
-
A.
Loading cargo too low
-
B.
Loading cargo too high or unevenly
-
C.
Driving too slowly
-
D.
Empty trailers
Correct answer: B.
Stacking cargo too high or loading unevenly raises the center of gravity and rollover risk.
Question 9 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 10 of 25 · Mountain Driving
When should you use lower gears?
-
A.
On steep upgrades and downgrades
-
B.
In flat terrain
-
C.
In stop-and-go traffic only
-
D.
Never in a combination vehicle
Correct answer: A.
Use lower gears on grades to maintain torque and engine braking.
Question 11 of 25 · Inspection
When checking the trailer air supply, you should:
-
A.
Charge the trailer with air, then disconnect the supply hose to test trailer emergency brakes
-
B.
Pump the brakes
-
C.
Disconnect the trailer power cord
-
D.
Open the trailer service line manually
Correct answer: A.
Disconnecting the supply line tests that the trailer emergency brakes apply automatically.
Question 12 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
Question 13 of 25 · CDL Rules
Which is true about long combination vehicles (LCVs)?
-
A.
They are easier to maneuver in tight spaces
-
B.
They require additional driver training and special permits
-
C.
They handle the same as single trailers
-
D.
They never require special routes
Correct answer: B.
LCVs need extra training, certifications, and often follow restricted routes.
Question 14 of 25 · Inspection
When should you check trailer brakes during operation?
-
A.
First few miles after coupling
-
B.
Every fuel stop
-
C.
Just at the end of the trip
-
D.
Never during the trip
Correct answer: A.
Test trailer brakes early in the trip to make sure they are functioning correctly.
Question 15 of 25 · Combination Air
Trailer brakes are required to be:
-
A.
Adjusted properly and matched to tractor brakes
-
B.
Stronger than tractor brakes
-
C.
Disengaged on level roads
-
D.
Off when empty
Correct answer: A.
Trailer brakes must be in proper adjustment and balance with tractor brakes.
Question 16 of 25 · Coupling
What are landing gear used for?
-
A.
Supporting the front of the trailer when uncoupled
-
B.
Steering the trailer
-
C.
Powering the trailer brakes
-
D.
Lighting the trailer
Correct answer: A.
Landing gear holds up the trailer when it is not connected to a tractor.
Question 17 of 25 · Skids
How can you correct a tractor jackknife?
-
A.
Apply the brakes harder
-
B.
Steer in the direction of the skid and accelerate gently
-
C.
Stop steering input
-
D.
Release the brakes and counter-steer
Correct answer: D.
Release the brakes to regain traction; counter-steer carefully to recover.
Question 18 of 25 · Vehicle Dynamics
When you turn suddenly with a high center of gravity, the trailer can:
-
A.
Roll over
-
B.
Stop more quickly
-
C.
Track better
-
D.
Reduce fuel use
Correct answer: A.
High centers of gravity make trailers prone to rollover during sharp turns.
Question 19 of 25 · Coupling
What is the proper position for the fifth wheel?
-
A.
Tilted down toward the rear of the tractor with jaws open
-
B.
Pointed straight up
-
C.
Locked and ready
-
D.
Removed for inspection
Correct answer: A.
Before coupling, the fifth wheel should tilt down toward the rear with the jaws open.
Question 20 of 25 · Combination Air
What is glad hands?
-
A.
Trailer doors
-
B.
Couplers used to join air lines from the tractor to the trailer
-
C.
Mirror brackets
-
D.
Brake levers
Correct answer: B.
Glad hands connect the service and emergency air lines between tractor and trailer.
Question 21 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 22 of 25 · Cargo
How do you know the trailer is properly loaded?
-
A.
Cargo is centered, balanced, and properly secured
-
B.
Cargo extends beyond the trailer ends
-
C.
Cargo is stacked unevenly
-
D.
Cargo is on top of the cab
Correct answer: A.
Centered, balanced, and secured loads handle predictably.
Question 23 of 25 · Skids
What should you do to recover from a trailer skid?
-
A.
Apply more brake pressure
-
B.
Release the brakes to allow trailer wheels to roll again
-
C.
Steer hard right
-
D.
Accelerate forward
Correct answer: B.
Release brakes to let trailer wheels roll, then steer to recover direction.
Question 24 of 25 · Skids
How can drivers avoid jackknifing?
-
A.
Brake gently and look ahead
-
B.
Adjust speed for road and weather
-
C.
Use ABS where equipped
-
D.
All of the above
Correct answer: D.
Smooth braking, appropriate speed, and ABS all reduce jackknife risk.
Question 25 of 25 · Vehicle Dynamics
What's the safest way to handle a tight turn with a long combination?
-
A.
Take it wide using both lanes if necessary
-
B.
Drive as fast as possible to maintain momentum
-
C.
Use the trailer hand valve
-
D.
Make a tight turn
Correct answer: A.
Take wider turns to avoid hitting curbs or other vehicles due to off-tracking.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The New York State Department of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your New York CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Skids: 6 questions
- Coupling: 5 questions
- Vehicle Dynamics: 3 questions
- Combination Air: 3 questions
- Inspection: 3 questions
- Cargo: 2 questions
- Following Distance: 1 question
- Mountain Driving: 1 question
- CDL Rules: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for New York until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.