25 realistic Air Brakes practice questions for Utah CDL applicants. Required for: Vehicles equipped with air brake systems. Official test: 25 questions, 20 correct to pass.
Question 1 of 25 · Speed Management
Air brake lag distance at 55 mph on dry pavement adds about:
-
A.
12 feet to stopping distance
-
B.
32 feet to stopping distance
-
C.
50 feet to stopping distance
-
D.
100 feet to stopping distance
Correct answer: B.
Air brake systems have a lag of about 0.4 seconds, adding roughly 32 feet at 55 mph.
Question 2 of 25 · Speed Management
Why is it important not to over-apply the brakes?
-
A.
Brakes can overheat and fade
-
B.
Brakes will lock and skid
-
C.
You may lose control of the vehicle
-
D.
All of the above
Correct answer: D.
Over-application leads to fade, lockup, skidding, and loss of control.
Question 3 of 25 · Gauges
You should know your vehicle is properly equipped with which gauge?
-
A.
Two air pressure gauges (or one with two needles) showing pressure in primary and secondary tanks
-
B.
A vacuum gauge
-
C.
A voltage meter only
-
D.
A coolant gauge only
Correct answer: A.
Dual air systems require gauges for both primary and secondary air supplies.
Question 4 of 25 · Spring Brakes
If your vehicle has dual parking control valves, you can use pressure from a separate tank to:
-
A.
Charge the trailer brakes
-
B.
Release the spring brakes to move a short distance if the main system loses air
-
C.
Operate the steering
-
D.
Power the air horn
Correct answer: B.
Dual parking control valves let you temporarily release spring brakes from a backup tank.
Question 5 of 25 · Compressor
The air compressor governor controls:
-
A.
When the air compressor will pump air into the storage tanks
-
B.
When the brakes are applied
-
C.
When emergency brakes engage
-
D.
How fast the air compressor turns
Correct answer: A.
The governor cuts the compressor in and out to keep the system within its operating pressure range.
Question 6 of 25 · Tanks
When should you drain the air tanks?
-
A.
Once a week
-
B.
Only when the warning light is on
-
C.
At the end of each working day
-
D.
Once a month
Correct answer: C.
Drain tanks completely at the end of each working day to remove water and oil.
Question 7 of 25 · Inspection
What is the air loss rate for combination vehicles with brakes applied?
-
A.
1 psi per minute
-
B.
2 psi per minute
-
C.
3 psi per minute
-
D.
4 psi per minute
Correct answer: D.
Combination vehicles can lose up to 4 psi per minute with brakes applied.
Question 8 of 25 · Gauges
The supply pressure gauge tells you:
-
A.
The pressure of brake fluid
-
B.
How much air pressure is in the air tanks
-
C.
The trailer brake pressure
-
D.
The temperature of the brake
Correct answer: B.
The supply gauge shows the air pressure available in the storage tanks.
Question 9 of 25 · Inspection
When should you push the brake pedal during the air brake test?
-
A.
Only when the engine is running
-
B.
When checking the compressor
-
C.
When the engine is off, to check that pressure does not drop too quickly
-
D.
During the brake light test only
Correct answer: C.
Apply firm pressure with the engine off to check for excessive air leakage from the system.
Question 10 of 25 · Spring Brakes
Modulating control valves do what?
-
A.
Drain water from tanks
-
B.
Apply spring brakes gradually using a hand control
-
C.
Open the trailer supply line
-
D.
Switch to emergency brakes
Correct answer: B.
Modulating valves let you apply the spring brakes gradually rather than all at once.
Question 11 of 25 · ABS
If the ABS warning light comes on, you should:
-
A.
Stop driving immediately
-
B.
Continue, knowing brakes still work — but ABS may not
-
C.
Pump the brakes constantly
-
D.
Engage the trailer hand valve
Correct answer: B.
You still have normal braking; only the ABS function may be off. Get it fixed soon.
Question 12 of 25 · Compressor
What is the purpose of a one-way check valve?
-
A.
Allow air to flow in one direction
-
B.
Allow water to drain
-
C.
Prevent the trailer from moving
-
D.
Increase pressure in the supply tank
Correct answer: A.
It permits airflow in one direction only — protecting the system if the compressor fails.
Question 13 of 25 · Foundation Brakes
What's the most common type of foundation brake found on heavy vehicles?
-
A.
Disc brakes
-
B.
Wedge drum brakes
-
C.
S-cam drum brakes
-
D.
Air-over-hydraulic
Correct answer: C.
S-cam drum brakes are the most common foundation brakes on heavy commercial vehicles.
Question 14 of 25 · Spring Brakes
What does the term "modulating control valve" refer to?
-
A.
A valve to regulate engine RPM
-
B.
A hand-operated valve that gradually applies the spring brakes
-
C.
A device that drains air tanks
-
D.
The trailer hand valve
Correct answer: B.
A modulating control valve allows gradual application of spring brakes for emergency or backup use.
Question 15 of 25 · Compressor
If the air compressor governor is not working properly:
-
A.
Air compressor may not maintain enough pressure to safely operate the brakes
-
B.
The brakes will work harder
-
C.
Brakes may not release at all
-
D.
There is no impact on safety
Correct answer: A.
A faulty governor can cause low system pressure or over-pressurization, both unsafe.
Question 16 of 25 · Speed Management
Which of these statements is true about brake fading?
-
A.
Resting brakes does not bring back braking power
-
B.
Brake fade is caused by drums getting too hot
-
C.
Brake fade only affects new vehicles
-
D.
Brake fade only happens with disc brakes
Correct answer: B.
Brake fade results from overheated drums or discs reducing friction and braking ability.
Question 17 of 25 · Compressor
What is the purpose of an alcohol evaporator?
-
A.
Reduce alcohol in the driver's system
-
B.
Reduce risk of frozen brake valves and lines in cold weather
-
C.
Improve fuel economy
-
D.
Lubricate the air compressor
Correct answer: B.
Alcohol injected into the air system reduces freeze-up risk in cold conditions.
Question 18 of 25 · System Basics
Air brake systems combine three different braking systems. They are:
-
A.
Service, parking, and emergency brakes
-
B.
Hydraulic, parking, and emergency brakes
-
C.
Front, rear, and trailer brakes
-
D.
Disc, drum, and parking brakes
Correct answer: A.
The three are: the service brake, the parking brake, and the emergency brake.
Question 19 of 25 · Operation
When the brake pedal is pushed harder, what happens?
-
A.
Brake pedal must be pumped to release
-
B.
More air goes to the brakes; less foot pressure releases air
-
C.
It locks the brakes permanently
-
D.
The brakes do not respond
Correct answer: B.
The harder you push, the more air pressure is sent to the brake chambers.
Question 20 of 25 · Inspection
Air leaks during a static brake check could indicate:
-
A.
Faulty brake chambers or air lines
-
B.
Engine problems
-
C.
Bad tires
-
D.
Low fuel pressure
Correct answer: A.
Air leaks usually indicate faulty chambers, lines, fittings, or valves.
Question 21 of 25 · Parking
On a tractor with no trailer attached, the tractor parking brake control:
-
A.
Will lock and unlock the front brakes
-
B.
Will set or release the spring brakes on the tractor
-
C.
Has no function
-
D.
Operates only the trailer brakes
Correct answer: B.
The yellow diamond control sets and releases the tractor parking (spring) brakes.
Question 22 of 25 · Tanks
Why must air tanks be drained?
-
A.
To remove fuel from the system
-
B.
To remove water and compressor oil that can damage the brakes
-
C.
To inspect the tanks
-
D.
To increase pressure
Correct answer: B.
Water and oil collect in tanks. They damage seals and can freeze in cold weather.
Question 23 of 25 · Spring Brakes
Where are spring brakes typically NOT found?
-
A.
Front steering axle
-
B.
Drive axles
-
C.
Trailer axles
-
D.
Tractor rear axles
Correct answer: A.
Spring brakes are found on drive axles and trailer axles, not normally on the steering axle.
Question 24 of 25 · Foundation Brakes
When checking the slack adjuster on S-cam brakes, the slack adjuster should not move more than:
-
A.
1/2 inch
-
B.
1 inch
-
C.
About 1 inch where the push rod attaches to it
-
D.
2 inches
Correct answer: C.
When pulled by hand, the slack adjuster shouldn't move more than about an inch where the push rod attaches.
Question 25 of 25 · Inspection
How do you know that you have an air leak?
-
A.
Pressure drops faster than allowable rate
-
B.
You hear hissing
-
C.
Both A and B
-
D.
The brake pedal feels firm
Correct answer: C.
Pressure dropping faster than allowed and audible hissing both indicate leaks.
About the Air Brakes Test
The Air Brakes test covers air brake system parts (compressor, governor, reservoirs, drain valves, alcohol evaporator, safety valve, brake pedal, foundation brakes), dual air brake systems, inspecting air brakes, using air brakes (normal stops, emergency stops, parking brakes), and proper procedures for braking on downgrades. If you fail or skip the Air Brakes test, your CDL is restricted to vehicles without full air brake systems.
The Utah Driver License Division administers this knowledge test as part of its commercial driver license program. To earn the Air Brakes Endorsement on your Utah CDL, you need to score at least 20 out of 25 on the official version.
Topics covered on this practice test
- Spring Brakes: 4 questions
- Compressor: 4 questions
- Inspection: 4 questions
- Speed Management: 3 questions
- Gauges: 2 questions
- Tanks: 2 questions
- Foundation Brakes: 2 questions
- ABS: 1 question
- System Basics: 1 question
- Operation: 1 question
- Parking: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Utah until you're ready for the official exam.
Tips specific to the Air Brakes test
Air Brakes questions test your ability to identify components, follow inspection sequences, and respond to system failures. Memorize the cut-in and cut-out pressures, the low-pressure warning thresholds, the pressure ranges at which spring brakes apply, and the maximum allowable air-loss rates. Many questions have nearly-identical wording, so precision matters.