25 realistic Combination Vehicles practice questions for Utah CDL applicants. Required for: Class A CDL (tractor-trailer combinations). Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Coupling
Before backing under a trailer, you should:
-
A.
Make sure the trailer brakes are set and the trailer is at the correct height
-
B.
Disconnect the air lines
-
C.
Lower the landing gear
-
D.
Engage the parking brake
Correct answer: A.
Confirm trailer brakes are locked and trailer height matches the fifth wheel.
Question 2 of 25 · Following Distance
What is "rear-end collision" risk for combination vehicles?
-
A.
It is reduced when carrying long cargo
-
B.
They have a higher risk because of long stopping distances and rear blind spots
-
C.
They have no greater risk
-
D.
Only for empty rigs
Correct answer: B.
Long stopping distance and rear blind spots increase rear-end collision risk.
Question 3 of 25 · Vehicle Dynamics
Which of these is true about the front trailer of a doubles or triples?
-
A.
It is less likely to overturn
-
B.
It is more stable
-
C.
It is more likely to overturn than the rear trailer
-
D.
It does not need brakes
Correct answer: A.
The front trailer in a combination is generally more stable than the rear trailer.
Question 4 of 25 · Coupling
You should NEVER:
-
A.
Back under a trailer at an angle
-
B.
Inspect the fifth wheel
-
C.
Use the parking brake
-
D.
Tug-test the kingpin
Correct answer: A.
Backing at an angle can damage the kingpin or push the trailer sideways.
Question 5 of 25 · Coupling
When you finish coupling, the air lines should be:
-
A.
Connected to the proper glad hands and supported off the catwalk and the deck plate
-
B.
Coiled tightly on top of the trailer
-
C.
Loose so they can move freely
-
D.
Disconnected
Correct answer: A.
Air lines must be connected and supported off the deck so they don't snag or wear.
Question 6 of 25 · Operation
Which of these is most important when driving with a trailer?
-
A.
Use the engine retarder constantly
-
B.
Use proper braking and signaling
-
C.
Drive at maximum speed limits
-
D.
Skip pre-trip checks if running late
Correct answer: B.
Proper braking and clear signaling are essential to safe combination driving.
Question 7 of 25 · Skids
What is "tractor jackknife"?
-
A.
Tractor drive wheels skid and the trailer pushes the tractor sideways
-
B.
Trailer wheels skid
-
C.
Steering wheels skid
-
D.
Engine fails
Correct answer: A.
When drive wheels skid, the trailer can push the tractor sideways into a jackknife.
Question 8 of 25 · Coupling
What does a "low coupling" condition look like?
-
A.
Trailer is too high above the fifth wheel
-
B.
Trailer is at the right height
-
C.
Trailer is too low and tractor frame can hit the trailer
-
D.
Trailer is angled to the right
Correct answer: C.
A trailer too low can damage the tractor frame as it slides under it.
Question 9 of 25 · Vehicle Dynamics
Which of these is true about driving combination vehicles?
-
A.
They are easier to handle than single vehicles
-
B.
They are more likely to roll over and jackknife
-
C.
They use less fuel per mile
-
D.
They need fewer mirrors
Correct answer: B.
Combination vehicles require more skill and are more prone to rollovers and jackknives.
Question 10 of 25 · Skids
Tractor jackknife occurs when:
-
A.
Drive wheels lose traction and skid
-
B.
The trailer wheels lock
-
C.
The trailer slides forward
-
D.
Steering wheels lock
Correct answer: A.
Drive wheels skidding cause tractor jackknife; trailer wheels skidding cause trailer jackknife.
Question 11 of 25 · Cargo
Why is securement of cargo essential?
-
A.
To prevent the load from shifting
-
B.
To prevent injury to others
-
C.
To prevent damage to the vehicle
-
D.
All of the above
Correct answer: D.
Securement protects the load, prevents shifts that affect handling, and protects others.
Question 12 of 25 · Coupling
What is the kingpin?
-
A.
A pin in the engine
-
B.
A vertical pin on the front of the trailer that locks into the fifth wheel
-
C.
A part of the air brake system
-
D.
A type of warning device
Correct answer: B.
The kingpin slides into the fifth wheel jaws to lock the trailer to the tractor.
Question 13 of 25 · Mountain Driving
When should you use lower gears?
-
A.
On steep upgrades and downgrades
-
B.
In flat terrain
-
C.
In stop-and-go traffic only
-
D.
Never in a combination vehicle
Correct answer: A.
Use lower gears on grades to maintain torque and engine braking.
Question 14 of 25 · Vehicle Dynamics
Empty trucks have what kind of stopping distance compared to fully loaded ones?
-
A.
Shorter
-
B.
Same
-
C.
Longer
-
D.
Half
Correct answer: C.
Empty rigs have less traction on drive axles and require greater stopping distance.
Question 15 of 25 · Skids
How can you correct a tractor jackknife?
-
A.
Apply the brakes harder
-
B.
Steer in the direction of the skid and accelerate gently
-
C.
Stop steering input
-
D.
Release the brakes and counter-steer
Correct answer: D.
Release the brakes to regain traction; counter-steer carefully to recover.
Question 16 of 25 · Coupling
What should you do before connecting air lines?
-
A.
Clean the rubber seals on the glad hands
-
B.
Lubricate them with oil
-
C.
Replace the seals every trip
-
D.
Heat them up
Correct answer: A.
Clean glad hand seals before connecting to ensure a good air seal.
Question 17 of 25 · Vehicle Dynamics
What is "off-tracking"?
-
A.
When the rear wheels follow a different path than the front wheels
-
B.
When the trailer slides off the road
-
C.
When the trailer is improperly loaded
-
D.
A type of fifth wheel
Correct answer: A.
In turns, rear wheels travel a smaller arc than the front, causing off-tracking.
Question 18 of 25 · Vehicle Dynamics
Off-tracking is most pronounced in:
-
A.
Single vehicles
-
B.
Long combinations and curves
-
C.
Empty trailers
-
D.
Vehicles with disc brakes
Correct answer: B.
Longer wheelbases and tighter curves cause greater off-tracking.
Question 19 of 25 · Inspection
What is the proper way to test the parking brakes after coupling?
-
A.
Apply trailer parking brake and try to gently pull forward
-
B.
Drive at normal speed
-
C.
Apply foot brake repeatedly
-
D.
Disconnect glad hands
Correct answer: A.
A gentle pull forward with parking brakes set confirms holding power.
Question 20 of 25 · Coupling
Which is true about pulling away after coupling?
-
A.
Test that the kingpin is locked by gently pulling forward against the trailer brakes
-
B.
Pull away as quickly as possible
-
C.
Lower the landing gear before pulling away
-
D.
Disconnect the air lines first
Correct answer: A.
A pull-test confirms the kingpin is locked before driving away.
Question 21 of 25 · Combination Air
Trailer brakes are required to be:
-
A.
Adjusted properly and matched to tractor brakes
-
B.
Stronger than tractor brakes
-
C.
Disengaged on level roads
-
D.
Off when empty
Correct answer: A.
Trailer brakes must be in proper adjustment and balance with tractor brakes.
Question 22 of 25 · Skids
What can cause a trailer skid in a combination vehicle?
-
A.
Locked trailer wheels and over-application of brakes
-
B.
Light loads on the trailer
-
C.
Tight steering at low speed
-
D.
High pressure in steering tires
Correct answer: A.
Locked trailer wheels cause trailer skid; reduce brake pressure to recover.
Question 23 of 25 · Cargo
How do you know the trailer is properly loaded?
-
A.
Cargo is centered, balanced, and properly secured
-
B.
Cargo extends beyond the trailer ends
-
C.
Cargo is stacked unevenly
-
D.
Cargo is on top of the cab
Correct answer: A.
Centered, balanced, and secured loads handle predictably.
Question 24 of 25 · CDL Rules
Which is true about long combination vehicles (LCVs)?
-
A.
They are easier to maneuver in tight spaces
-
B.
They require additional driver training and special permits
-
C.
They handle the same as single trailers
-
D.
They never require special routes
Correct answer: B.
LCVs need extra training, certifications, and often follow restricted routes.
Question 25 of 25 · Inspection
When inspecting your trailer's wheels, what should you look for?
-
A.
Loose or missing nuts
-
B.
Cracked or broken wheel rims
-
C.
Bent or broken studs
-
D.
All of the above
Correct answer: D.
Inspect for loose nuts, cracks, bent studs, and other defects on every pre-trip.
About the Combination Vehicles Test
The Combination Vehicles test covers driving combination vehicles safely, combination vehicle air brakes, antilock brake systems, coupling and uncoupling, and inspecting a combination vehicle. Combination vehicles are usually heavier, longer, and require more driving skill than single commercial vehicles. They are also more likely to roll over and jackknife.
The Utah Driver License Division administers this knowledge test as part of its commercial driver license program. To earn the Combination Vehicles on your Utah CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 7 questions
- Vehicle Dynamics: 5 questions
- Skids: 4 questions
- Cargo: 2 questions
- Inspection: 2 questions
- Following Distance: 1 question
- Operation: 1 question
- Mountain Driving: 1 question
- Combination Air: 1 question
- CDL Rules: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Utah until you're ready for the official exam.
Tips specific to the Combination Vehicles test
Combination Vehicles questions cover off-tracking, jackknifing, coupling and uncoupling, the fifth wheel, kingpin, glad hands, landing gear, and the special air-brake considerations for tractor-trailer combinations. Expect detailed step-by-step coupling questions.