25 realistic Doubles and Triples practice questions for Washington CDL applicants. Required for: Drivers pulling more than one trailer. Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Hazard Awareness
What is "blind spot" risk for doubles and triples?
-
A.
It's minimal due to long mirrors
-
B.
It's significant especially behind and to the right
-
C.
It's only at night
-
D.
It only affects single trailers
Correct answer: B.
Long combinations have large blind spots — especially behind and to the right.
Question 2 of 25 · Coupling
Where should the heaviest trailer go in a doubles or triples set?
-
A.
First (closest to the tractor)
-
B.
Last (farthest from the tractor)
-
C.
Anywhere
-
D.
In the middle
Correct answer: A.
Place the heaviest trailer behind the tractor for best stability.
Question 3 of 25 · Vehicle Dynamics
Doubles and triples have ____ rollover risk than single trailers.
-
A.
Lower
-
B.
Higher
-
C.
The same
-
D.
No rollover risk
Correct answer: B.
Multiple trailers have higher rollover risk because of greater articulation and "crack-the-whip" effect.
Question 4 of 25 · Following Distance
What's the best way to manage following distance with doubles?
-
A.
Maintain extra distance compared to single trailers
-
B.
Same as single trailers
-
C.
Less distance
-
D.
No following distance needed
Correct answer: A.
Doubles need more space because of longer stopping distances and reduced visibility.
Question 5 of 25 · Lane Changes
What's the major risk when changing lanes with doubles or triples?
-
A.
The rear trailer may not follow exactly
-
B.
Other vehicles may not see the long combination
-
C.
The trailer may swing out
-
D.
All of the above
Correct answer: D.
Visibility and rear-trailer tracking are both major lane-change risks.
Question 6 of 25 · Cargo
What's the impact of overloading a trailer in a doubles set?
-
A.
Increased rollover risk
-
B.
Poor handling
-
C.
Brake problems
-
D.
All of the above
Correct answer: D.
Overloading creates a chain of safety problems for the whole combination.
Question 7 of 25 · Following Distance
What's the safe way to handle a doubles in heavy traffic?
-
A.
Maintain extra following distance and signal early
-
B.
Speed up to keep with traffic
-
C.
Use the shoulder
-
D.
Drive aggressively
Correct answer: A.
Extra space and early signals are critical in heavy traffic with combinations.
Question 8 of 25 · Coupling
What is the pintle hook?
-
A.
A coupling device on the dolly that connects to the lead trailer's pintle plate
-
B.
A type of tire
-
C.
A safety chain
-
D.
A brake component
Correct answer: A.
The pintle hook on the dolly connects to the lead trailer for towing.
Question 9 of 25 · Emergency Maneuvers
How should doubles drivers handle emergency braking?
-
A.
Apply brakes firmly but smoothly
-
B.
Use only the trailer hand valve
-
C.
Pump the brakes
-
D.
Use only the engine retarder
Correct answer: A.
Smooth, firm braking is best — let ABS work if equipped.
Question 10 of 25 · Coupling
What's the role of safety chains on a converter dolly?
-
A.
To support the dolly when uncoupled
-
B.
To prevent the trailer from coming loose if the pintle hook fails
-
C.
To improve traction
-
D.
To act as a brake
Correct answer: B.
Safety chains keep the trailer attached if the pintle hook fails.
Question 11 of 25 · Inspection
Why must drivers inspect the dolly before connecting?
-
A.
To check for damage and proper operation
-
B.
To verify the brakes work
-
C.
To inspect the pintle hook
-
D.
All of the above
Correct answer: D.
Dolly inspection includes structure, brakes, and pintle hook condition.
Question 12 of 25 · Combination Air
What's the role of glad hands in doubles and triples?
-
A.
They connect air lines between each unit
-
B.
They are coupling devices
-
C.
They are safety chains
-
D.
They are landing gear
Correct answer: A.
Glad hands connect service and emergency air lines between every unit.
Question 13 of 25 · Skids
What should you do if a trailer starts to skid?
-
A.
Release the brakes to allow trailer wheels to roll
-
B.
Apply more brake
-
C.
Steer hard right
-
D.
Accelerate
Correct answer: A.
Release brakes to let trailer wheels roll; steer to recover.
Question 14 of 25 · Vehicle Dynamics
When making a turn, the front trailer of a doubles set:
-
A.
Tracks like a single trailer
-
B.
Off-tracks more than the tractor
-
C.
Stays in line with the tractor
-
D.
Off-tracks less than the rear trailer
Correct answer: D.
The rear trailer off-tracks more than the front, so the rear is more likely to hit obstacles.
Question 15 of 25 · Vehicle Dynamics
How do you reduce off-tracking in doubles?
-
A.
Make wider turns
-
B.
Slow down
-
C.
Use mirrors carefully
-
D.
All of the above
Correct answer: D.
Wider turns, slower speed, and careful mirror use minimize off-tracking impact.
Question 16 of 25 · CDL Rules
Triples are illegal in many states because:
-
A.
They are too long and cause traffic disruption
-
B.
They have higher rollover risk
-
C.
They require special permits
-
D.
All of the above
Correct answer: D.
Many states prohibit triples due to length, rollover risk, and special permitting needs.
Question 17 of 25 · Communication
How can drivers communicate effectively when driving doubles?
-
A.
Use turn signals well in advance
-
B.
Use mirrors continuously
-
C.
Use the horn when needed
-
D.
All of the above
Correct answer: D.
Clear, early signals, mirrors, and horn use all improve safety.
Question 18 of 25 · Coupling
What is the converter dolly?
-
A.
A type of tractor
-
B.
A coupling device used between trailers in doubles and triples
-
C.
A trailer brake
-
D.
A type of cargo
Correct answer: B.
The converter dolly connects two trailers in a combination set.
Question 19 of 25 · Speed Management
How should drivers approach a sharp curve with doubles?
-
A.
Slow down well before the curve and steer smoothly
-
B.
Maintain highway speed
-
C.
Use engine retarder
-
D.
Brake hard in the curve
Correct answer: A.
Slow down before the curve; smooth steering through the curve avoids rollover.
Question 20 of 25 · Inspection
When inspecting doubles and triples, what should you check?
-
A.
Each trailer's lights and brakes
-
B.
Each converter dolly
-
C.
Each fifth wheel and pintle hook
-
D.
All of the above
Correct answer: D.
Inspect every trailer, dolly, fifth wheel, and pintle hook before driving.
Question 21 of 25 · Coupling
How do you prevent a trailer from rolling away when uncoupled?
-
A.
Apply trailer brakes and chock the wheels
-
B.
Use the parking brake on the tractor
-
C.
Lower the landing gear quickly
-
D.
Drive away quickly
Correct answer: A.
Set trailer brakes and chock wheels to prevent any roll while uncoupling.
Question 22 of 25 · Coupling
What's the proper procedure for coupling a second trailer?
-
A.
Position the dolly under the second trailer, then back the lead trailer to the dolly
-
B.
Drive the lead trailer over the dolly
-
C.
Connect electrical first
-
D.
Lower the landing gear
Correct answer: A.
Position the dolly first, then back the lead trailer to it for proper coupling.
Question 23 of 25 · Coupling
How should you uncouple a converter dolly?
-
A.
Lower the dolly support, disconnect, and pull the tractor and first trailer away
-
B.
Disconnect and drive away
-
C.
Use the trailer parking brake
-
D.
Cut the air lines
Correct answer: A.
Lower support, disconnect lines and pin, then pull the lead unit away.
Question 24 of 25 · Mountain Driving
What's the recommended speed when descending a steep grade with doubles?
-
A.
Slow speed using lower gears and engine braking
-
B.
Posted speed limit
-
C.
Faster than single trailers
-
D.
Use service brakes only
Correct answer: A.
Use lower gears and engine braking. Service brakes only intermittently.
Question 25 of 25 · Vehicle Dynamics
What's the importance of "leverage" in doubles and triples?
-
A.
Each trailer affects the others; the rear can amplify or reduce stability
-
B.
It only affects fuel efficiency
-
C.
It doesn't matter
-
D.
It only affects loading
Correct answer: A.
Forces transfer between trailers; each one affects the stability of the combination.
About the Doubles and Triples Test
The Doubles and Triples test covers pulling double and triple trailers, coupling and uncoupling, inspecting doubles and triples, antilock brake systems, and safe driving with multiple trailers. Doubles and triples are more likely to roll over than single trailers and are extremely sensitive to steering inputs at the rear trailer.
The Washington Department of Licensing administers this knowledge test as part of its commercial driver license program. To earn the Doubles/Triples (T) on your Washington CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 7 questions
- Vehicle Dynamics: 4 questions
- Following Distance: 2 questions
- Inspection: 2 questions
- Hazard Awareness: 1 question
- Lane Changes: 1 question
- Cargo: 1 question
- Emergency Maneuvers: 1 question
- Combination Air: 1 question
- Skids: 1 question
- CDL Rules: 1 question
- Communication: 1 question
- Speed Management: 1 question
- Mountain Driving: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Washington until you're ready for the official exam.
Tips specific to the Doubles and Triples test
Doubles and Triples questions emphasize the "crack-the-whip" effect, converter dolly inspection and use, pintle hooks, safety chains, the heaviest-trailer-first loading rule, and the higher rollover risk of multi-trailer combinations. Many states prohibit triples; check local rules.