25 realistic Air Brakes practice questions for Mississippi CDL applicants. Required for: Vehicles equipped with air brake systems. Official test: 25 questions, 20 correct to pass.
Question 1 of 25 · Operation
When the brake pedal is pushed harder, what happens?
-
A.
Brake pedal must be pumped to release
-
B.
More air goes to the brakes; less foot pressure releases air
-
C.
It locks the brakes permanently
-
D.
The brakes do not respond
Correct answer: B.
The harder you push, the more air pressure is sent to the brake chambers.
Question 2 of 25 · Spring Brakes
What does the term "modulating control valve" refer to?
-
A.
A valve to regulate engine RPM
-
B.
A hand-operated valve that gradually applies the spring brakes
-
C.
A device that drains air tanks
-
D.
The trailer hand valve
Correct answer: B.
A modulating control valve allows gradual application of spring brakes for emergency or backup use.
Question 3 of 25 · Speed Management
Why is it important not to over-apply the brakes?
-
A.
Brakes can overheat and fade
-
B.
Brakes will lock and skid
-
C.
You may lose control of the vehicle
-
D.
All of the above
Correct answer: D.
Over-application leads to fade, lockup, skidding, and loss of control.
Question 4 of 25 · Spring Brakes
Where are spring brakes typically NOT found?
-
A.
Front steering axle
-
B.
Drive axles
-
C.
Trailer axles
-
D.
Tractor rear axles
Correct answer: A.
Spring brakes are found on drive axles and trailer axles, not normally on the steering axle.
Question 5 of 25 · Compressor
The air compressor governor controls:
-
A.
When the air compressor will pump air into the storage tanks
-
B.
When the brakes are applied
-
C.
When emergency brakes engage
-
D.
How fast the air compressor turns
Correct answer: A.
The governor cuts the compressor in and out to keep the system within its operating pressure range.
Question 6 of 25 · Inspection
How can you check the slack adjusters?
-
A.
Pull hard on each slack adjuster — they should not move more than about 1 inch
-
B.
Listen for air leaks at each chamber
-
C.
Watch the brake light flash
-
D.
Look at the brake pedal travel
Correct answer: A.
Pulling hard, slack adjusters should not move more than about 1 inch where the push rod attaches.
Question 7 of 25 · Spring Brakes
Modulating control valves do what?
-
A.
Drain water from tanks
-
B.
Apply spring brakes gradually using a hand control
-
C.
Open the trailer supply line
-
D.
Switch to emergency brakes
Correct answer: B.
Modulating valves let you apply the spring brakes gradually rather than all at once.
Question 8 of 25 · Compressor
What is the purpose of a one-way check valve?
-
A.
Allow air to flow in one direction
-
B.
Allow water to drain
-
C.
Prevent the trailer from moving
-
D.
Increase pressure in the supply tank
Correct answer: A.
It permits airflow in one direction only — protecting the system if the compressor fails.
Question 9 of 25 · Inspection
How much air pressure (psi) loss is allowed per minute for combination vehicles with the engine off and brakes released?
-
A.
Up to 1 psi
-
B.
Up to 2 psi
-
C.
Up to 3 psi
-
D.
Up to 4 psi
Correct answer: B.
Combination vehicles allow up to 3 psi loss per minute with brakes released; with brakes applied, up to 4 psi.
Question 10 of 25 · Parking
Why should you use chocks?
-
A.
When parking on a hill
-
B.
On level ground when leaving the vehicle
-
C.
Whenever brakes might fail or it's required by company policy or law
-
D.
All of the above
Correct answer: D.
Chocks should be used when required to prevent vehicle movement.
Question 11 of 25 · Speed Management
Air brake lag is:
-
A.
The time required for the brakes to apply after the pedal is pressed
-
B.
The amount of free play in the brake pedal
-
C.
The distance traveled before the brakes release
-
D.
The time to drain air tanks
Correct answer: A.
Lag is the time between pressing the pedal and the brakes actually applying — about 0.4 seconds.
Question 12 of 25 · System Basics
Which of the following is NOT in the air brake system?
-
A.
Brake chambers
-
B.
Slack adjusters
-
C.
S-cam
-
D.
Hydraulic master cylinder
Correct answer: D.
Hydraulic master cylinders are part of hydraulic systems, not air brake systems.
Question 13 of 25 · Foundation Brakes
Brake drums (or discs) must not have cracks longer than:
-
A.
1/4 the width of the friction area
-
B.
1/2 the width of the friction area
-
C.
3/4 the width of the friction area
-
D.
Anything is acceptable
Correct answer: B.
Cracks longer than one-half the width of the friction area are a safety violation.
Question 14 of 25 · Combination Air
When a tractor protection valve closes, it:
-
A.
Opens the air supply to the trailer
-
B.
Stops air from going to the trailer brakes
-
C.
Causes the parking brake to release
-
D.
Has no effect on the trailer
Correct answer: B.
When closed, it stops airflow to the trailer and applies trailer emergency brakes.
Question 15 of 25 · Parking
You should never use the trailer hand valve to park because:
-
A.
It is not strong enough
-
B.
The air could leak out, releasing the brakes
-
C.
It only applies the front brakes
-
D.
It is not connected to the trailer
Correct answer: B.
If air leaks out, the brakes release. Always use the parking brake to park.
Question 16 of 25 · Inspection
Which of the following must be checked before operating an air-braked vehicle?
-
A.
Low air pressure warning signal
-
B.
Spring brakes set automatically
-
C.
Air leakage rate
-
D.
All of the above
Correct answer: D.
All of these are required pre-trip air brake checks.
Question 17 of 25 · Operation
When making a normal stop, what should you do?
-
A.
Push the brake pedal down so you can stop at a safe place and remain in control
-
B.
Pump the brakes
-
C.
Use only the parking brake
-
D.
Use only the trailer hand valve
Correct answer: A.
Apply pressure progressively to come to a smooth, safe stop while maintaining control.
Question 18 of 25 · Gauges
The supply pressure gauge tells you:
-
A.
The pressure of brake fluid
-
B.
How much air pressure is in the air tanks
-
C.
The trailer brake pressure
-
D.
The temperature of the brake
Correct answer: B.
The supply gauge shows the air pressure available in the storage tanks.
Question 19 of 25 · Gauges
What gauge tells you the air pressure being delivered to the brakes?
-
A.
Application pressure gauge
-
B.
Supply pressure gauge
-
C.
Speedometer
-
D.
Tachometer
Correct answer: A.
The application gauge shows pressure being applied to the brakes when the pedal is pressed.
Question 20 of 25 · Foundation Brakes
What's the most common type of foundation brake found on heavy vehicles?
-
A.
Disc brakes
-
B.
Wedge drum brakes
-
C.
S-cam drum brakes
-
D.
Air-over-hydraulic
Correct answer: C.
S-cam drum brakes are the most common foundation brakes on heavy commercial vehicles.
Question 21 of 25 · Tanks
When should you drain the air tanks?
-
A.
Once a week
-
B.
Only when the warning light is on
-
C.
At the end of each working day
-
D.
Once a month
Correct answer: C.
Drain tanks completely at the end of each working day to remove water and oil.
Question 22 of 25 · System Basics
Air brakes use compressed air to:
-
A.
Lubricate the wheels
-
B.
Make the brakes work
-
C.
Cool the engine
-
D.
Increase fuel pressure
Correct answer: B.
Compressed air is the working fluid that applies the brakes in an air brake system.
Question 23 of 25 · Emergency Maneuvers
Which of these statements is true about emergency braking?
-
A.
Pumping the brakes is always best
-
B.
Stab braking is for non-ABS vehicles in emergencies
-
C.
You should brake harder than necessary
-
D.
Stab braking is the same as pumping
Correct answer: B.
Stab braking applies to non-ABS systems: full application until lockup, then release.
Question 24 of 25 · Inspection
How much air pressure (psi) loss is allowed per minute for single vehicles with the engine off and brakes released?
-
A.
Up to 1 psi
-
B.
Up to 2 psi
-
C.
Up to 3 psi
-
D.
Up to 4 psi
Correct answer: B.
Single vehicles allow up to 2 psi per minute with brakes released; up to 3 psi with brakes applied.
Question 25 of 25 · Spring Brakes
Spring brakes will come on automatically when air pressure drops to:
-
A.
100 psi
-
B.
60 psi or less
-
C.
20 to 45 psi
-
D.
10 psi
Correct answer: C.
Spring brakes typically apply automatically between 20 and 45 psi.
About the Air Brakes Test
The Air Brakes test covers air brake system parts (compressor, governor, reservoirs, drain valves, alcohol evaporator, safety valve, brake pedal, foundation brakes), dual air brake systems, inspecting air brakes, using air brakes (normal stops, emergency stops, parking brakes), and proper procedures for braking on downgrades. If you fail or skip the Air Brakes test, your CDL is restricted to vehicles without full air brake systems.
The Mississippi Department of Public Safety — Driver Services administers this knowledge test as part of its commercial driver license program. To earn the Air Brakes Endorsement on your Mississippi CDL, you need to score at least 20 out of 25 on the official version.
Topics covered on this practice test
- Spring Brakes: 4 questions
- Inspection: 4 questions
- Operation: 2 questions
- Speed Management: 2 questions
- Compressor: 2 questions
- Parking: 2 questions
- System Basics: 2 questions
- Foundation Brakes: 2 questions
- Gauges: 2 questions
- Combination Air: 1 question
- Tanks: 1 question
- Emergency Maneuvers: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Mississippi until you're ready for the official exam.
Tips specific to the Air Brakes test
Air Brakes questions test your ability to identify components, follow inspection sequences, and respond to system failures. Memorize the cut-in and cut-out pressures, the low-pressure warning thresholds, the pressure ranges at which spring brakes apply, and the maximum allowable air-loss rates. Many questions have nearly-identical wording, so precision matters.