25 realistic Doubles and Triples practice questions for Vermont CDL applicants. Required for: Drivers pulling more than one trailer. Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Skids
What should you do if a trailer starts to skid?
-
A.
Release the brakes to allow trailer wheels to roll
-
B.
Apply more brake
-
C.
Steer hard right
-
D.
Accelerate
Correct answer: A.
Release brakes to let trailer wheels roll; steer to recover.
Question 2 of 25 · Operation
How should drivers approach intersections with doubles or triples?
-
A.
Slow down and signal early to allow for the turn
-
B.
Drive at full speed
-
C.
Cut across lanes if needed
-
D.
Use the engine retarder
Correct answer: A.
Slow down and signal well in advance to give time for the long combination.
Question 3 of 25 · Emergency Maneuvers
How should doubles drivers handle emergency braking?
-
A.
Apply brakes firmly but smoothly
-
B.
Use only the trailer hand valve
-
C.
Pump the brakes
-
D.
Use only the engine retarder
Correct answer: A.
Smooth, firm braking is best — let ABS work if equipped.
Question 4 of 25 · Communication
How can drivers communicate effectively when driving doubles?
-
A.
Use turn signals well in advance
-
B.
Use mirrors continuously
-
C.
Use the horn when needed
-
D.
All of the above
Correct answer: D.
Clear, early signals, mirrors, and horn use all improve safety.
Question 5 of 25 · Operation
What's the safest way to merge into traffic with doubles?
-
A.
Use turn signals early and merge gradually
-
B.
Speed up to merge quickly
-
C.
Force other drivers to yield
-
D.
Drive on the shoulder
Correct answer: A.
Signal early and merge gradually so other drivers can adjust.
Question 6 of 25 · Coupling
What's a common mistake when coupling doubles?
-
A.
Not properly aligning the dolly with the second trailer
-
B.
Forgetting to connect air lines
-
C.
Not testing the brakes
-
D.
All of the above
Correct answer: D.
Alignment, air lines, and brake tests are common areas for mistakes.
Question 7 of 25 · Coupling
What's a "spider" or "dolly converter"?
-
A.
A type of trailer
-
B.
A coupling device with a fifth wheel mounted on a single axle
-
C.
A type of brake
-
D.
A safety chain
Correct answer: B.
Converter dollies have a fifth wheel and an axle to allow connecting trailers.
Question 8 of 25 · Vehicle Dynamics
Doubles and triples have ____ rollover risk than single trailers.
-
A.
Lower
-
B.
Higher
-
C.
The same
-
D.
No rollover risk
Correct answer: B.
Multiple trailers have higher rollover risk because of greater articulation and "crack-the-whip" effect.
Question 9 of 25 · Lane Changes
What's the major risk when changing lanes with doubles or triples?
-
A.
The rear trailer may not follow exactly
-
B.
Other vehicles may not see the long combination
-
C.
The trailer may swing out
-
D.
All of the above
Correct answer: D.
Visibility and rear-trailer tracking are both major lane-change risks.
Question 10 of 25 · Coupling
Where should the heaviest trailer go in a doubles or triples set?
-
A.
First (closest to the tractor)
-
B.
Last (farthest from the tractor)
-
C.
Anywhere
-
D.
In the middle
Correct answer: A.
Place the heaviest trailer behind the tractor for best stability.
Question 11 of 25 · Vehicle Dynamics
How do you reduce off-tracking in doubles?
-
A.
Make wider turns
-
B.
Slow down
-
C.
Use mirrors carefully
-
D.
All of the above
Correct answer: D.
Wider turns, slower speed, and careful mirror use minimize off-tracking impact.
Question 12 of 25 · Speed Management
What's the safe speed for taking corners with doubles or triples?
-
A.
Posted speed limit
-
B.
Slower than single trailers
-
C.
Higher than single trailers
-
D.
No different from single trailers
Correct answer: B.
Take corners more slowly than single trailers due to greater rollover risk.
Question 13 of 25 · Vehicle Dynamics
What is "crack-the-whip"?
-
A.
A driver discipline rule
-
B.
When the rear trailer swings out due to sudden steering inputs
-
C.
A type of weight distribution
-
D.
A coupling procedure
Correct answer: B.
The rear trailer can swing far wider than the tractor, magnifying steering inputs.
Question 14 of 25 · Cargo
Doubles and triples are most stable when:
-
A.
All trailers are properly loaded
-
B.
Trailers are empty
-
C.
The lead trailer is empty
-
D.
The rear trailer is heaviest
Correct answer: A.
Proper loading on every trailer is key to stability.
Question 15 of 25 · Inspection
Why is it important to inspect each trailer separately?
-
A.
Each trailer has its own systems and potential issues
-
B.
It's easier to spot problems
-
C.
It's required by law
-
D.
All of the above
Correct answer: D.
Each trailer needs its own inspection of brakes, lights, and condition.
Question 16 of 25 · Coupling
What's the role of safety chains on a converter dolly?
-
A.
To support the dolly when uncoupled
-
B.
To prevent the trailer from coming loose if the pintle hook fails
-
C.
To improve traction
-
D.
To act as a brake
Correct answer: B.
Safety chains keep the trailer attached if the pintle hook fails.
Question 17 of 25 · Mountain Driving
What's the recommended speed when descending a steep grade with doubles?
-
A.
Slow speed using lower gears and engine braking
-
B.
Posted speed limit
-
C.
Faster than single trailers
-
D.
Use service brakes only
Correct answer: A.
Use lower gears and engine braking. Service brakes only intermittently.
Question 18 of 25 · Combination Air
What's the role of glad hands in doubles and triples?
-
A.
They connect air lines between each unit
-
B.
They are coupling devices
-
C.
They are safety chains
-
D.
They are landing gear
Correct answer: A.
Glad hands connect service and emergency air lines between every unit.
Question 19 of 25 · Hazard Awareness
What is "blind spot" risk for doubles and triples?
-
A.
It's minimal due to long mirrors
-
B.
It's significant especially behind and to the right
-
C.
It's only at night
-
D.
It only affects single trailers
Correct answer: B.
Long combinations have large blind spots — especially behind and to the right.
Question 20 of 25 · Cargo
Which is true about loading doubles and triples?
-
A.
Light to heavy from rear to front is a common rule
-
B.
Heaviest trailer should be at the rear
-
C.
Loading order doesn't matter
-
D.
All trailers should be empty
Correct answer: A.
Generally place heavier trailers nearest the tractor for stability.
Question 21 of 25 · Backing
When backing doubles or triples, you should:
-
A.
Avoid backing if possible
-
B.
Use a helper as a spotter
-
C.
Back slowly and carefully
-
D.
All of the above
Correct answer: D.
Avoid backing combinations; use a spotter and go slowly when you must.
Question 22 of 25 · Vehicle Dynamics
What's the importance of "leverage" in doubles and triples?
-
A.
Each trailer affects the others; the rear can amplify or reduce stability
-
B.
It only affects fuel efficiency
-
C.
It doesn't matter
-
D.
It only affects loading
Correct answer: A.
Forces transfer between trailers; each one affects the stability of the combination.
Question 23 of 25 · Inspection
Why must drivers inspect the dolly before connecting?
-
A.
To check for damage and proper operation
-
B.
To verify the brakes work
-
C.
To inspect the pintle hook
-
D.
All of the above
Correct answer: D.
Dolly inspection includes structure, brakes, and pintle hook condition.
Question 24 of 25 · Following Distance
What's the best way to manage following distance with doubles?
-
A.
Maintain extra distance compared to single trailers
-
B.
Same as single trailers
-
C.
Less distance
-
D.
No following distance needed
Correct answer: A.
Doubles need more space because of longer stopping distances and reduced visibility.
Question 25 of 25 · Adverse Conditions
What's the safest way to handle wind with doubles or triples?
-
A.
Slow down and grip the wheel firmly
-
B.
Speed up to clear the area
-
C.
Use engine retarder
-
D.
Lock the brakes
Correct answer: A.
Reduce speed and steer firmly. Wind affects long combinations more than singles.
About the Doubles and Triples Test
The Doubles and Triples test covers pulling double and triple trailers, coupling and uncoupling, inspecting doubles and triples, antilock brake systems, and safe driving with multiple trailers. Doubles and triples are more likely to roll over than single trailers and are extremely sensitive to steering inputs at the rear trailer.
The Vermont Department of Motor Vehicles administers this knowledge test as part of its commercial driver license program. To earn the Doubles/Triples (T) on your Vermont CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 4 questions
- Vehicle Dynamics: 4 questions
- Operation: 2 questions
- Cargo: 2 questions
- Inspection: 2 questions
- Skids: 1 question
- Emergency Maneuvers: 1 question
- Communication: 1 question
- Lane Changes: 1 question
- Speed Management: 1 question
- Mountain Driving: 1 question
- Combination Air: 1 question
- Hazard Awareness: 1 question
- Backing: 1 question
- Following Distance: 1 question
- Adverse Conditions: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for Vermont until you're ready for the official exam.
Tips specific to the Doubles and Triples test
Doubles and Triples questions emphasize the "crack-the-whip" effect, converter dolly inspection and use, pintle hooks, safety chains, the heaviest-trailer-first loading rule, and the higher rollover risk of multi-trailer combinations. Many states prohibit triples; check local rules.