25 realistic Doubles and Triples practice questions for New Jersey CDL applicants. Required for: Drivers pulling more than one trailer. Official test: 20 questions, 16 correct to pass.
Question 1 of 25 · Coupling
What is the pintle hook?
-
A.
A coupling device on the dolly that connects to the lead trailer's pintle plate
-
B.
A type of tire
-
C.
A safety chain
-
D.
A brake component
Correct answer: A.
The pintle hook on the dolly connects to the lead trailer for towing.
Question 2 of 25 · Inspection
Why must drivers inspect the dolly before connecting?
-
A.
To check for damage and proper operation
-
B.
To verify the brakes work
-
C.
To inspect the pintle hook
-
D.
All of the above
Correct answer: D.
Dolly inspection includes structure, brakes, and pintle hook condition.
Question 3 of 25 · Coupling
What's the role of safety chains on a converter dolly?
-
A.
To support the dolly when uncoupled
-
B.
To prevent the trailer from coming loose if the pintle hook fails
-
C.
To improve traction
-
D.
To act as a brake
Correct answer: B.
Safety chains keep the trailer attached if the pintle hook fails.
Question 4 of 25 · Coupling
How should you uncouple a converter dolly?
-
A.
Lower the dolly support, disconnect, and pull the tractor and first trailer away
-
B.
Disconnect and drive away
-
C.
Use the trailer parking brake
-
D.
Cut the air lines
Correct answer: A.
Lower support, disconnect lines and pin, then pull the lead unit away.
Question 5 of 25 · CDL Rules
Why are doubles and triples drivers required to have additional training?
-
A.
They handle differently and require more skill
-
B.
Federal regulations require training
-
C.
They have higher rollover risk
-
D.
All of the above
Correct answer: D.
Skill, regulation, and rollover risk all justify extra training.
Question 6 of 25 · Lane Changes
What's the major risk when changing lanes with doubles or triples?
-
A.
The rear trailer may not follow exactly
-
B.
Other vehicles may not see the long combination
-
C.
The trailer may swing out
-
D.
All of the above
Correct answer: D.
Visibility and rear-trailer tracking are both major lane-change risks.
Question 7 of 25 · Inspection
What's the impact of poor maintenance on doubles or triples?
-
A.
Increased risk of breakdowns and accidents
-
B.
Poor fuel efficiency
-
C.
Legal issues
-
D.
All of the above
Correct answer: D.
Poor maintenance leads to safety, efficiency, and legal problems.
Question 8 of 25 · Following Distance
What's the safe way to handle a doubles in heavy traffic?
-
A.
Maintain extra following distance and signal early
-
B.
Speed up to keep with traffic
-
C.
Use the shoulder
-
D.
Drive aggressively
Correct answer: A.
Extra space and early signals are critical in heavy traffic with combinations.
Question 9 of 25 · Coupling
What's the proper procedure for coupling a second trailer?
-
A.
Position the dolly under the second trailer, then back the lead trailer to the dolly
-
B.
Drive the lead trailer over the dolly
-
C.
Connect electrical first
-
D.
Lower the landing gear
Correct answer: A.
Position the dolly first, then back the lead trailer to it for proper coupling.
Question 10 of 25 · Vehicle Dynamics
What's the importance of "leverage" in doubles and triples?
-
A.
Each trailer affects the others; the rear can amplify or reduce stability
-
B.
It only affects fuel efficiency
-
C.
It doesn't matter
-
D.
It only affects loading
Correct answer: A.
Forces transfer between trailers; each one affects the stability of the combination.
Question 11 of 25 · Cargo
Doubles and triples are most stable when:
-
A.
All trailers are properly loaded
-
B.
Trailers are empty
-
C.
The lead trailer is empty
-
D.
The rear trailer is heaviest
Correct answer: A.
Proper loading on every trailer is key to stability.
Question 12 of 25 · Coupling
What's a common mistake when coupling doubles?
-
A.
Not properly aligning the dolly with the second trailer
-
B.
Forgetting to connect air lines
-
C.
Not testing the brakes
-
D.
All of the above
Correct answer: D.
Alignment, air lines, and brake tests are common areas for mistakes.
Question 13 of 25 · Combination Air
What's the role of glad hands in doubles and triples?
-
A.
They connect air lines between each unit
-
B.
They are coupling devices
-
C.
They are safety chains
-
D.
They are landing gear
Correct answer: A.
Glad hands connect service and emergency air lines between every unit.
Question 14 of 25 · Coupling
How do you prevent a trailer from rolling away when uncoupled?
-
A.
Apply trailer brakes and chock the wheels
-
B.
Use the parking brake on the tractor
-
C.
Lower the landing gear quickly
-
D.
Drive away quickly
Correct answer: A.
Set trailer brakes and chock wheels to prevent any roll while uncoupling.
Question 15 of 25 · Coupling
What's a "spider" or "dolly converter"?
-
A.
A type of trailer
-
B.
A coupling device with a fifth wheel mounted on a single axle
-
C.
A type of brake
-
D.
A safety chain
Correct answer: B.
Converter dollies have a fifth wheel and an axle to allow connecting trailers.
Question 16 of 25 · Cargo
What's the consequence of bad weight distribution in doubles?
-
A.
Increased rollover risk
-
B.
Poor handling
-
C.
Tire wear
-
D.
All of the above
Correct answer: D.
Bad distribution increases rollover, handling problems, and tire wear.
Question 17 of 25 · Vehicle Dynamics
What is "crack-the-whip"?
-
A.
A driver discipline rule
-
B.
When the rear trailer swings out due to sudden steering inputs
-
C.
A type of weight distribution
-
D.
A coupling procedure
Correct answer: B.
The rear trailer can swing far wider than the tractor, magnifying steering inputs.
Question 18 of 25 · Coupling
What is the converter dolly?
-
A.
A type of tractor
-
B.
A coupling device used between trailers in doubles and triples
-
C.
A trailer brake
-
D.
A type of cargo
Correct answer: B.
The converter dolly connects two trailers in a combination set.
Question 19 of 25 · Speed Management
What's the safe speed for taking corners with doubles or triples?
-
A.
Posted speed limit
-
B.
Slower than single trailers
-
C.
Higher than single trailers
-
D.
No different from single trailers
Correct answer: B.
Take corners more slowly than single trailers due to greater rollover risk.
Question 20 of 25 · Backing
When backing doubles or triples, you should:
-
A.
Avoid backing if possible
-
B.
Use a helper as a spotter
-
C.
Back slowly and carefully
-
D.
All of the above
Correct answer: D.
Avoid backing combinations; use a spotter and go slowly when you must.
Question 21 of 25 · Adverse Conditions
What's the safe way to handle a doubles or triples on a wet road?
-
A.
Reduce speed and increase following distance
-
B.
Drive at posted speed
-
C.
Use chains
-
D.
Both A and C
Correct answer: A.
Slower speeds and more space are essential on wet roads.
Question 22 of 25 · Emergency Maneuvers
How should doubles drivers handle emergency braking?
-
A.
Apply brakes firmly but smoothly
-
B.
Use only the trailer hand valve
-
C.
Pump the brakes
-
D.
Use only the engine retarder
Correct answer: A.
Smooth, firm braking is best — let ABS work if equipped.
Question 23 of 25 · Vehicle Dynamics
When making a turn, the front trailer of a doubles set:
-
A.
Tracks like a single trailer
-
B.
Off-tracks more than the tractor
-
C.
Stays in line with the tractor
-
D.
Off-tracks less than the rear trailer
Correct answer: D.
The rear trailer off-tracks more than the front, so the rear is more likely to hit obstacles.
Question 24 of 25 · Coupling
Where should the heaviest trailer go in a doubles or triples set?
-
A.
First (closest to the tractor)
-
B.
Last (farthest from the tractor)
-
C.
Anywhere
-
D.
In the middle
Correct answer: A.
Place the heaviest trailer behind the tractor for best stability.
Question 25 of 25 · Following Distance
What's the best way to manage following distance with doubles?
-
A.
Maintain extra distance compared to single trailers
-
B.
Same as single trailers
-
C.
Less distance
-
D.
No following distance needed
Correct answer: A.
Doubles need more space because of longer stopping distances and reduced visibility.
About the Doubles and Triples Test
The Doubles and Triples test covers pulling double and triple trailers, coupling and uncoupling, inspecting doubles and triples, antilock brake systems, and safe driving with multiple trailers. Doubles and triples are more likely to roll over than single trailers and are extremely sensitive to steering inputs at the rear trailer.
The New Jersey Motor Vehicle Commission administers this knowledge test as part of its commercial driver license program. To earn the Doubles/Triples (T) on your New Jersey CDL, you need to score at least 16 out of 20 on the official version.
Topics covered on this practice test
- Coupling: 9 questions
- Vehicle Dynamics: 3 questions
- Inspection: 2 questions
- Following Distance: 2 questions
- Cargo: 2 questions
- CDL Rules: 1 question
- Lane Changes: 1 question
- Combination Air: 1 question
- Speed Management: 1 question
- Backing: 1 question
- Adverse Conditions: 1 question
- Emergency Maneuvers: 1 question
How to use this practice test
- Read each question carefully. CDL questions are written precisely — small wording differences matter.
- Click "Show Answers & Explanations" only after answering every question. Don't peek mid-test.
- Read the explanation for every question, even ones you got right. The reasoning is more important than the answer.
- Repeat the test until you score 100%. The questions are deterministic per state, so you can track your improvement over multiple sessions.
- Move on to the other endorsement tests for New Jersey until you're ready for the official exam.
Tips specific to the Doubles and Triples test
Doubles and Triples questions emphasize the "crack-the-whip" effect, converter dolly inspection and use, pintle hooks, safety chains, the heaviest-trailer-first loading rule, and the higher rollover risk of multi-trailer combinations. Many states prohibit triples; check local rules.